- 您现在的位置：买卖IC网 > PDF目录10105 > LTC2367HMS-18#TRPBF (Linear Technology)IC ADC 18BIT 500K 1CH 16MSOP PDF资料下载
参数资料
| 型号： | LTC2367HMS-18#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 3/24页 |
| 文件大小： | 0K |
| 描述： | IC ADC 18BIT 500K 1CH 16MSOP |
| 产品培训模块： | LTC2369- 18-/16-bit Pseudo-Differential SAR ADC Family Overview |
| 标准包装： | 2,500 |
| 位数： | 18 |
| 采样率（每秒）： | 500k |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 8mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TFSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 16-MSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个伪差分，单极 |
| 配用： | DC1813A-G-ND - BOARD SAR ADC LTC2367-18 |
LTC2367-18
11
236718f
APPLICATIONS INFORMATION
INPUT DRIVE CIRCUITS
A low impedance source can directly drive the high im-
pedance input of the LTC2367-18 without gain error. A
high impedance source should be buffered to minimize
settling time during acquisition and to optimize the dis-
tortion performance of the ADC. Minimizing settling time
is important even for DC inputs, because the ADC input
draws a current spike when entering acquisition.
For best performance, a buffer amplifier should be used
to drive the analog input of the LTC2367-18. The ampli-
fier provides low output impedance, which produces fast
settling of the analog signal during the acquisition phase.
It also provides isolation between the signal source and
the current spike the ADC input draws.
Input Filtering
The noise and distortion of the buffer amplifier and signal
sourcemustbeconsideredsincetheyaddtotheADCnoise
and distortion. Noisy input signals should be filtered prior
to the buffer amplifier input with an appropriate filter to
minimizenoise.Thesimple1-poleRClowpassfilter(LPF1)
shown in Figure 4 is sufficient for many applications.
High quality capacitors and resistors should be used in the
RCfilterssincethesecomponentscanadddistortion.NPO
and silver mica type dielectric capacitors have excellent
linearity. Carbon surface mount resistors can generate
distortion from self heating and from damage that may
occurduringsoldering.Metalfilmsurfacemountresistors
are much less susceptible to both problems.
Pseudo-Differential Unipolar Inputs
For most applications, we recommend the low power
LT6202 ADC driver to drive the LTC2367-18. With a low
noise density of 1.9nV/√Hz and a low supply current of
3mA, the LT6202 is flexible and may be configured to
convert signals of various amplitudes to the 0V to 5V input
range of the LTC2367-18.
To achieve the full distortion performance of the
LTC2367-18, a low distortion single-ended signal source
driven through the LT6202 configured as a unity-gain buf-
fer as shown in Figure 4 can be used to get the full data
sheet THD specification of –120dB.
The LT6202 can also be used to buffer and convert large
true bipolar signals which swing below ground to the 0V
to 5V input range of the LTC2367-18. Figure 5a shows the
LT6202 being used to convert a ±10V true bipolar signal
for use by the LTC2367-18. In this case, the LT6202 is
configured as an inverting amplifier stage, which acts to
attenuateandlevelshifttheinputsignaltothe0Vto5Vinput
rangeoftheLTC2367-18.Intheinvertingconfiguration,the
single-ended input signal source no longer directly drives
a high impedance input. The input impedance is instead
set by resistor RIN. RIN must be chosen carefully based on
the source impedance of the signal source. Higher values
of RIN tend to degrade both the noise and distortion of
the LT6202 and LTC2367-18 as a system. Table 1 shows
the resulting SNR and THD for several values of RIN, R1,
R2, R3 and R4 in this configuration. Figure 5b shows the
resultingFFTwhenusingtheLT6202asshowninFigure5a.
Figure 4. Input Signal Chain
Another filter network consisting of LPF2 should be used
between the buffer and ADC input to both minimize the
noisecontributionofthebufferandtohelpminimizedistur-
bances reflected into the buffer from sampling transients.
Long RC time constants at the analog inputs will slow
down the settling of the analog inputs. Therefore, LPF2
requires a wider bandwidth than LPF1. A buffer amplifier
with a low noise density must be selected to minimize
degradation of the SNR.
10
10nF
66nF
50
LPF2
LPF1
BW = 1.6MHz
BW = 48kHz
LTC2367-18
IN+
IN–
236718 F04
–
+
LT6202
VREF
0V
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1742IFW | IC ADC SMPL 14BIT 65MSPS 48TSSOP |
| VI-232-IW-F3 | CONVERTER MOD DC/DC 15V 100W |
| VI-BNV-MW-F4 | CONVERTER MOD DC/DC 5.8V 100W |
| IDT72V205L15TFI8 | IC FIFO SYNC 16KX9 15NS 64QFP |
| VI-233-IW-F1 | CONVERTER MOD DC/DC 24V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2367IDE-16#PBF | 功能描述:IC ADC 16BIT SPI/SRL 500K 16-DFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| LTC2367IDE-16#TRPBF | 功能描述:IC ADC 16BIT SPI/SRL 500K 16-DFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| LTC2367IDE-18#PBF | 功能描述:IC ADC 18BIT 500K 1CH 16DFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| LTC2367IDE-18#TRPBF | 功能描述:IC ADC 18BIT 500K 1CH 16DFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| LTC2367IMS-16#PBF | 功能描述:IC ADC 16BIT SPI/SRL 500K 16MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
发布紧急采购，3分钟左右您将得到回复。