- 您现在的位置：买卖IC网 > PDF目录10527 > LTC2392CUK-16#PBF (Linear Technology)IC ADC 16BIT SER/PAR 500K 48QFN PDF资料下载
参数资料
| 型号： | LTC2392CUK-16#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 25/26页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT SER/PAR 500K 48QFN |
| 标准包装： | 52 |
| 位数： | 16 |
| 采样率（每秒）： | 500k |
| 数据接口： | 串行，并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 135mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-WFQFN 裸露焊盘 |
| 供应商设备封装： | 48-QFN-EP（7x7） |
| 包装： | 管件 |
| 输入数目和类型： | 1 个差分，双极 |
| 产品目录页面： | 1349 (CN2011-ZH PDF) |
| 配用： | DC1500A-B-ND - BOARD SAR ADC LTC2392-16 |
LTC2392-16
8
239216fa
pin Functions
GND (Pins 1, 5, 7, 20, 35, 41, 44, 48, Exposed Pad Pin
49): Ground. All GND pins must be connected to a solid
ground plane. Exposed pad must be soldered directly to
the ground plane.
AVP (Pins 2, 40, 45, 46, 47): 5V Analog Power Supply.
The range of AVP is 4.75V to 5.25V. Bypass AVP to GND
with a good quality 0.1F and a 10F ceramic capacitor
in parallel.
DVP (Pins 3, 19): 5V Digital Power Supply. The range of
DVP is 4.75V to 5.25V. Bypass DVP to GND with a good
quality 0.1F and a 10F ceramic capacitor in parallel.
SER/PAR (Pin 4): Serial/Parallel Selection Input. This pin
controls the digital interface. A logic high on this pin se-
lects the serial interface and a logic low selects the parallel
interface. In the serial mode the non-active digital outputs
are high impedance.
OB/2C (Pin 6): Offset Binary/Two’s Complement Input.
When OB/2C is high, the digital output is offset binary.
When low, the MSB is inverted resulting in two’s comple-
ment output.
BYTESWAP (Pin 8): BYTESWAP Input. With BYTESWAP
low, data will be output with Pin 28 (D15) being the MSB
and Pin 9 (D0) being the LSB. With BYTESWAP high, the
upper eight bits and the lower eight bits will be switched.
The MSB is output on Pin 16 and Bit 8 is output on Pin 9.
Bit 7 is output on Pin 28 and the LSB is output on Pin 21.
D0 (Pin 9): Data Bit 0. When SER/PAR = 0 this pin is Bit 0
of the parallel port data output bus.
D1 (Pin 10): Data Bit 1. When SER/PAR = 0 this pin is
Bit 1 of the parallel port data output bus.
D2 (Pin 11): Data Bit 2. When SER/PAR = 0 this pin is
Bit 2 of the parallel port data output bus.
D3 (Pin 12): Data Bit 3. When SER/PAR = 0 this pin is
Bit 3 of the parallel port data output bus.
D4 (Pin 13): Data Bit 4. When SER/PAR = 0 this pin is
Bit 4 of the parallel port data output bus.
D5 (Pin 14): Data Bit 5. When SER/PAR = 0 this pin is
Bit 5 of the parallel port data output bus.
D6 (Pin 15): Data Bit 6. When SER/PAR = 0 this pin is
Bit 6 of the parallel port data output bus.
D7 (Pin 16): Data Bit 7. When SER/PAR = 0 this pin is
Bit 7 of the parallel port data output bus.
OGND (Pin 17): Digital Ground for the Input/Output
Interface.
OVP (Pin 18): Digital Power Supply for the Input/Output
Interface. The range for OVP is 1.8V to 5V. Bypass OVP
to OGND with a good quality 4.7F ceramic capacitor
close to the pin.
D8 (Pin 21): Data Bit 8. When SER/PAR = 0 this pin is
Bit 8 of the parallel port data output bus.
D9/SDIN (Pin 22): Data Bit 9/Serial Data Input. When SER/
PAR = 0 this pin is Bit 9 of the parallel port data output bus.
When SER/PAR = 1, (serial mode) this is the serial data
input. SDIN can be used as a data input to daisy chain two
or more conversion results into a single SDOUT line. The
digital data level on SDIN is output on SDOUT with a delay
of 16 SCLK periods after the start of the read sequence.
D10/SDOUT(Pin23):DataBit10/SerialDataOutput.When
SER/PAR = 0 this pin is Bit 10 of the parallel port data
output bus. When SER/PAR = 1, (serial mode) this is the
serial data output. The conversion result can be clocked
out serially on this pin synchronized to SCLK. The data
is clocked out MSB first on the rising edge of SCLK and
is valid on the falling edge of SCLK. The data format is
determined by the logic level of OB/2C.
D11/SCLK (Pin 24): Data Bit 11/Serial Clock Input. When
SER/PAR = 0 this pin is Bit 11 of the parallel port data
output bus. When SER/PAR = 1, (serial mode) this is the
serial clock input.
D12 (Pin 25): Data Bit 12. When SER/PAR = 0 this pin is
Bit 12 of the parallel port data output bus.
D13 (Pin 26): Data Bit 13. When SER/PAR = 0 this pin is
Bit 13 of the parallel port data output bus.
D14 (Pin 27): Data Bit 14. When SER/PAR = 0 this pin is
Bit 14 of the parallel port data output bus.
相关PDF资料 |
PDF描述 |
|---|---|
| PT01E-10-6P | CONN RCPT 6 POS CBL MNT W/PINS |
| AD9634BCPZ-170 | IC ADC 12BIT 170MSPS 32-LFCSP |
| DS34LV87TM/NOPB | IC LINE DRIVER QUAD CMOS 16-SOIC |
| AD7711ANZ | IC ADC 24BIT RTD I SOURCE 24-DIP |
| AD9600ABCPZ-125 | IC ADC 10BIT 125MSPS 64LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2392HLX-16#PBF | 功能描述:IC ADC 16B SER/PAR 500K 48LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| LTC2392ILX-16#PBF | 功能描述:IC ADC 16B SER/PAR 500K 48LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| LTC2392IUK-16#PBF | 功能描述:IC ADC 16B SER/PAR 500K 48QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| LTC2392IUK-16#TRPBF | 功能描述:IC ADC 16B SER/PAR 500K 48QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| LTC2393CLX-16#PBF | 功能描述:IC ADC 16BIT SER/PAR 1M 48-LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
发布紧急采购，3分钟左右您将得到回复。