- 您现在的位置：买卖IC网 > PDF目录2006 > LTC2411-1IMS#TRPBF (Linear Technology)IC A/DCONV DIFF INPUT&REF 10MSOP PDF资料下载
参数资料
| 型号： | LTC2411-1IMS#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 3/40页 |
| 文件大小： | 0K |
| 描述： | IC A/DCONV DIFF INPUT&REF 10MSOP |
| 标准包装： | 2,500 |
| 位数： | 24 |
| 采样率（每秒）： | 6.8 |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 1mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个差分，双极 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
LTC2411/LTC2411-1
11
CONVERTER OPERATION
Converter Operation Cycle
The LTC2411/LTC2411-1 are low power, delta-sigma ana-
log-to-digital converters with an easy-to-use 3-wire serial
interface (see Figure 1). Their operation is made up of three
states. The converter operating cycle begins with the con-
version, followed by the low power sleep state and ends with
the data output (see Figure 2). The 3-wire interface consists
of serial data output (SDO), serial clock (SCK) and chip
select (CS).
Initially, the LTC2411/LTC2411-1 perform a conversion.
Once the conversion is complete, the devices enter the
sleep state. While in this sleep state, power consumption
is reduced by an order of magnitude. The parts remain in
the sleep state as long as CS is HIGH. The conversion
result is held indefinitely in a static shift register while the
converter is in the sleep state.
Once CS is pulled LOW, the devices begin outputting the
conversion result. There is no latency in the conversion
result. The data output corresponds to the conversion just
performed. This result is shifted out on the serial data out
pin (SDO) under the control of the serial clock (SCK). Data
is updated on the falling edge of SCK allowing the user to
reliably latch data on the rising edge of SCK (see Figure 3).
The data output state is concluded once 32 bits are read
out of the ADC or when CS is brought HIGH. The devices
automatically initiate a new conversion and the cycle
repeats.
Through timing control of the CS and SCK pins, the
LTC2411/LTC2411-1 offer several flexible modes of op-
eration (internal or external SCK and free-running conver-
sion modes). These various modes do not require
programming configuration registers; moreover, they do
not disturb the cyclic operation described above. These
modes of operation are described in detail in the Serial
Interface Timing Modes section.
Conversion Clock
A major advantage the delta-sigma converter offers over
conventional type converters is an on-chip digital filter
(commonly implemented as a Sinc or Comb filter). For
high resolution, low frequency applications, this filter is
typically designed to reject line frequencies of 50 or 60Hz
plus their harmonics. The filter rejection performance is
directly related to the accuracy of the converter system
clock. The LTC2411/LTC2411-1 incorporate a highly ac-
curate on-chip oscillator. This eliminates the need for
external frequency setting components such as crystals or
oscillators. Clocked by the on-chip oscillator, the LTC2411
achieves a minimum of 110dB rejection at the line fre-
quency (50Hz or 60Hz
±2%) and the LTC2411-1 achieves
a minimum of 87dB rejection over 49Hz to 61.2Hz.
Ease of Use
The LTC2411/LTC2411-1 data output has no latency,
filter settling delay or redundant data associated with the
conversion cycle. There is a one-to-one correspondence
between the conversion and the output data. Therefore,
multiplexing multiple analog voltages is easy.
The LTC2411/LTC2411-1 perform offset and full-scale
calibrations in every conversion cycle. This calibration is
transparent to the user and has no effect on the cyclic
operation described above. The advantage of continuous
calibration is extreme stability of offset and full-scale read-
ings with respect to time, supply voltage change and tem-
perature drift.
Power-Up Sequence
The LTC2411/LTC2411-1 automatically enter an internal
reset state when the power supply voltage VCC drops
below approximately 1.9V. This feature guarantees the
Figure 2. LTC2411/LTC2411-1 State Transition Diagram
CONVERT
SLEEP
DATA OUTPUT
2411 F02
TRUE
FALSE
CS = LOW
AND
SCK
APPLICATIO S I FOR ATIO
WU
UU
相关PDF资料 |
PDF描述 |
|---|---|
| LTC2418IGN#TRPBF | IC ADC 24BIT DIFF INPUT 28SSOP |
| LTC2431IMS#TRPBF | IC ADC 20BIT DIFFINPUT/REF10MSOP |
| LTC2433-1IMS#TRPBF | IC ADC DIFF 16BIT 3WIRE 10-MSOP |
| LTC2435CGN#TRPBF | IC ADC DIFF I/REF 20BIT 16-SSOP |
| LTC2442IG#PBF | IC ADC 24BIT 4CH 36-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2411CMS | 功能描述:IC A/D CONV 24BIT MICRPWR 10MSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2411CMS#PBF | 功能描述:IC A/D CONV 24BIT MICRPWR 10MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC2411CMS#TR | 功能描述:IC A/D CONV 24BIT MICRPWR 10MSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2411CMS#TRPBF | 功能描述:IC A/D CONV 24BIT MICRPWR 10MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2411IMS | 功能描述:IC A/D CONV 24BIT MICRPWR 10MSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。