- 您现在的位置：买卖IC网 > PDF目录10673 > LTC2414CGN#PBF (Linear Technology)IC ADC 8CH 24BIT DIFFINPUT28SSOP PDF资料下载
参数资料
| 型号： | LTC2414CGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 18/48页 |
| 文件大小： | 0K |
| 描述： | IC ADC 8CH 24BIT DIFFINPUT28SSOP |
| 标准包装： | 49 |
| 位数： | 24 |
| 采样率（每秒）： | 7.5 |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 1mW |
| 电压电源： | 单电源 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 管件 |
| 输入数目和类型： | 8 个单端，单极；8 个单端，双极；4 个差分，单极；4 个差分，双极 |
| 产品目录页面： | 1347 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
LTC2414/LTC2418
25
241418fa
operation, it is recommended to drive all digital input
signals to full CMOS levels [VIL < 0.4V and
VOH > (VCC – 0.4V)].
During the conversion period, the undershoot and/or
overshoot of a fast digital signal connected to the pins
may severely disturb the analog to digital conversion
process. Undershoot and overshoot can occur because of
the impedance mismatch at the converter pin when the
transition time of an external control signal is less than
twice the propagation delay from the driver to LTC2414/
LTC2418. For reference, on a regular FR-4 board, signal
propagation velocity is approximately 183ps/inch for
internal traces and 170ps/inch for surface traces. Thus, a
driver generating a control signal with a minimum transi-
tion time of 1ns must be connected to the converter pin
through a trace shorter than 2.5 inches. This problem
becomes particularly difficult when shared control lines
are used and multiple reflections may occur. The solution
is to carefully terminate all transmission lines close to
their characteristic impedance.
Parallel termination near the LTC2414/LTC2418 pin will
eliminate this problem but will increase the driver power
dissipation. A series resistor between 27
and 56
placed near the driver or near the LTC2414/LTC2418 pin
will also eliminate this problem without additional power
dissipation. The actual resistor value depends upon the
trace impedance and connection topology.
An alternate solution is to reduce the edge rate of the
control signals. It should be noted that using very slow
edges will increase the converter power supply current
during the transition time. The differential input and refer-
ence architecture reduce substantially the converter’s
sensitivity to ground currents.
Particular attention must be given to the connection of the
FO signal when the LTC2414/LTC2418 are used with an
external conversion clock. This clock is active during the
conversion time and the normal mode rejection provided
by the internal digital filter is not very high at this fre-
quency. A normal mode signal of this frequency at the
converter reference terminals may result into DC gain and
INL errors. A normal mode signal of this frequency at the
converter input terminals may result into a DC offset error.
APPLICATIO S I FOR ATIO
WU
UU
Such perturbations may occur due to asymmetric capaci-
tive coupling between the FO signal trace and the converter
input and/or reference connection traces. An immediate
solution is to maintain maximum possible separation
between the FO signal trace and the input/reference sig-
nals. When the FO signal is parallel terminated near the
converter, substantial AC current is flowing in the loop
formed by the FO connection trace, the termination and the
ground return path. Thus, perturbation signals may be
inductively coupled into the converter input and/or refer-
ence. In this situation, the user must reduce to a minimum
the loop area for the FO signal as well as the loop area for
the differential input and reference connections.
Driving the Input and Reference
The input and reference pins of the LTC2414/LTC2418
converters are directly connected to a network of sampling
capacitors. Depending upon the relation between the
differential input voltage and the differential reference
voltage, these capacitors are switching between these
four pins transferring small amounts of charge in the
process. A simplified equivalent circuit is shown in
Figure 11.
For a simple approximation, the source impedance RS
driving an analog input pin (IN+, IN–, REF+ or REF–) can be
considered to form, together with RSW and CEQ (see
Figure 11), a first order passive network with a time
constant
τ = (RS + RSW) CEQ. The converter is able to
sample the input signal with better than 1ppm accuracy if
the sampling period is at least 14 times greater than the
input circuit time constant
τ. The sampling process on the
four input analog pins is quasi-independent so each time
constant should be considered by itself and, under worst-
case circumstances, the errors may add.
When using the internal oscillator (FO = LOW or HIGH), the
LTC2414/LTC2418’s front-end switched-capacitor net-
work is clocked at 76800Hz corresponding to a 13
s
sampling period. Thus, for settling errors of less than
1ppm, the driving source impedance should be chosen
such that
τ ≤ 13s/14 = 920ns. When an external oscillator
of frequency fEOSC is used, the sampling period is 2/fEOSC
and, for a settling error of less than 1ppm,
τ ≤ 0.14/fEOSC.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-2V3-IX-B1 | CONVERTER MOD DC/DC 24V 75W |
| VI-2V1-IX-B1 | CONVERTER MOD DC/DC 12V 75W |
| VI-2TZ-IV-B1 | CONVERTER MOD DC/DC 2V 60W |
| VI-27T-IX-B1 | CONVERTER MOD DC/DC 6.5V 75W |
| VI-2TY-IV-B1 | CONVERTER MOD DC/DC 3.3V 99W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2414IGN | 功能描述:IC ADC 8CH 24BIT DIFFINPUT28SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2414IGN#PBF | 功能描述:IC ADC 8CH 24BIT DIFFINPUT28SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2414IGN#TR | 功能描述:IC ADC 8CH 24BIT DIFFINPUT28SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2414IGN#TRPBF | 功能描述:IC ADC 8CH 24BIT DIFFINPUT28SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2415-1CGN | 功能描述:IC ADC 24BIT DIFFINPUT/REF16SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。