- 您现在的位置：买卖IC网 > PDF目录10328 > LTC2430CGN#PBF (Linear Technology)IC ADC 20BIT DIFFINPUT/REF16SSOP PDF资料下载
参数资料
| 型号： | LTC2430CGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 4/40页 |
| 文件大小： | 0K |
| 描述： | IC ADC 20BIT DIFFINPUT/REF16SSOP |
| 标准包装： | 100 |
| 位数： | 20 |
| 采样率（每秒）： | 7.5 |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 1mW |
| 电压电源： | 单电源 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 管件 |
| 输入数目和类型： | 1 个差分，双极 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
LTC2430/LTC2431
12
24301f
Power-Up Sequence
The LTC2430/LTC2431 automatically enter an internal
reset state when the power supply voltage VCC drops
below approximately 2V. This feature guarantees the
integrity of the conversion result and of the serial interface
mode selection. (See the 2-wire I/O sections in the Serial
Interface Timing Modes section.)
When the VCC voltage rises above this critical threshold,
the LTC2430 or LTC2431 creates an internal power-on-
reset (POR) signal with a duration of approximately 1ms.
The POR signal clears all internal registers. Following the
POR signal, the converter starts a normal conversion
cycle and follows the succession of states described
above. The first conversion result following POR is accu-
rate within the specifications of the device if the power
supply voltage is restored within the operating range
(2.7V to 5.5V) before the end of the POR time interval.
Reference Voltage Range
The LTC2430/LTC2431 accept a differential external refer-
ence voltage. The absolute/common mode voltage speci-
fication for the REF+ and REF– pins covers the entire range
from GND to VCC. For correct converter operation, the
REF+ pin must always be more positive than the REF– pin.
The LTC2430/LTC2431 can accept a differential reference
voltage from 0.1V to VCC. The converter (LTC2430 or
LTC2431) output noise is determined by the thermal noise
of the front-end circuits, and, as such, its value in micro-
volts is nearly constant with reference voltage. A decrease
in reference voltage will not significantly improve the
converter’s effective resolution. On the other hand, a re-
duced reference voltage will improve the converter’s over-
all INL performance. A reduced reference voltage will also
improve the converter performance when operated with
an external conversion clock (external FO signal) at sub-
stantially higher output data rates.
Input Voltage Range
The analog input is truly differential with an absolute/com-
mon mode range for the IN+ and IN– input pins extending
from GND – 0.3V to VCC + 0.3V. Outside these limits, the
ESD protection devices begin to turn on and the errors due
to input leakage current increase rapidly. Within these lim-
its, the LTC2430 or LTC2431 converts the bipolar differen-
tial input signal, VIN = IN+ – IN–, from – FS = –0.5 VREF
to +FS = 0.5 VREF where VREF = REF+ – REF –. Outside this
range the converter indicates the overrange or the
underrange condition using distinct output codes.
Input signals applied to IN+ and IN– pins may extend by
300mV below ground and above VCC. In order to limit any
fault current, resistors of up to 5k may be added in series
with the IN+ and IN– pins without affecting the performance
of the device. In the physical layout, it is important to main-
tain the parasitic capacitance of the connection between
these series resistors and the corresponding pins as low
as possible; therefore, the resistors should be located as
close as practical to the pins. In addition, series resistors
will introduce a temperature dependent offset error due to
the input leakage current. A 1nA input leakage current will
develop a 1ppm offset error on a 5k resistor if VREF = 5V.
This error has a very strong temperature dependency.
Output Data Format
The LTC2430/LTC2431 serial output data stream is 24 bits
long. The first 3 bits represent status information indicat-
ing the sign and conversion state. The next 21 bits are the
conversion result, MSB first. The third and fourth bits to-
gether are also used to indicate an underrange condition
(the differential input voltage is below – FS) or an overrange
condition (the differential input voltage is above + FS).
Bit 23 (first output bit) is the end of conversion (EOC)
indicator. This bit is available at the SDO pin during the
conversion and sleep states whenever the CS pin is LOW.
This bit is HIGH during the conversion and goes LOW
when the conversion is complete.
Bit 22 (second output bit) is a dummy bit (DMY) and is
always LOW.
Bit 21 (third output bit) is the conversion result sign indi-
cator (SIG). If VIN is >0, this bit is HIGH. If VIN is <0, this
bit is LOW.
Bit 20 (fourth output bit) is the most significant bit (MSB)
of the result. This bit in conjunction with Bit 21 also
provides the underrange or overrange indication. If both
Bit 21 and Bit 20 are HIGH, the differential input voltage is
APPLICATIO S I FOR ATIO
WU
UU
相关PDF资料 |
PDF描述 |
|---|---|
| LTC2430CGN | IC ADC 20BIT DIFFINPUT/REF16SSOP |
| AD7914BRUZ-REEL7 | IC ADC 10BIT 4CH W/SEQ 16TSSOP |
| MS27473T14C35S | CONN PLUG 37POS STRAIGHT W/SCKT |
| AD7265BCPZ-REEL7 | IC ADC 12BIT 3CHAN 1MSPS 32LFCSP |
| AD9283BRSZ-RL80 | IC ADC 8BIT 80MSPS 3V 20-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2430IGN | 功能描述:IC ADC 20BIT DIFFINPUT/REF16SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2430IGN#PBF | 功能描述:IC ADC 20BIT DIFFINPUT/REF16SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2430IGN#TR | 功能描述:IC ADC 20BIT DIFFINPUT/REF16SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2430IGN#TRPBF | 功能描述:IC ADC 20BIT DIFFINPUT/REF16SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2431CMS | 功能描述:IC ADC 20BIT DIFFINPUT/REF10MSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
发布紧急采购，3分钟左右您将得到回复。