- 您现在的位置：买卖IC网 > PDF目录10320 > LTC2439-1IGN#PBF (Linear Technology)IC ADC 16BIT 16CH MCRPWR 28SSOP PDF资料下载
参数资料
| 型号： | LTC2439-1IGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 3/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 16CH MCRPWR 28SSOP |
| 标准包装： | 49 |
| 位数： | 16 |
| 采样率（每秒）： | 6.8 |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 1mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 管件 |
| 输入数目和类型： | 16 个单端，双极；8 个差分，双极 |
| 配用： | DC790A-ND - BOARD DELTA SIGMA ADC LTC2439-1 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC2439-1
11
24391fa
Input Data Format
When the LTC2439-1 is powered up, the default selection
used for the first conversion is IN+ = CH0 and IN– = CH1
(Address = 00000). In the data input/output mode follow-
ing the first conversion, a channel selection can be up-
dated using an 8-bit word. The LTC2439-1 serial input data
is clocked into the SDI pin on the rising edge of SCK (see
Figure 3a). The input is composed of an 8-bit word with the
first 3 bits acting as control bits and the remaining 5 bits
as the channel address bits.
The first 2 bits are always 10 for proper updating opera-
tion. The third bit is EN. For EN = 1, the following 5 bits are
used to update the input channel selection. For EN = 0,
previous channel selection is kept and the following bits
are ignored. Therefore, the address is updated when the 3
control bits are 101 and kept for 100. Alternatively, the 3
control bits can be all zero to keep the previous address.
This alternation is intended to simplify the SDI interface
allowing the user to simply connect SDI to ground if no
update is needed. Combinations other than 101, 100 and
000 of the 3 control bits should be avoided.
When update operation is set (101), the following 5 bits
are the channel address. The first bit, SGL, decides if the
differential selection mode (SGL = 0) or the single-ended
selection mode is used (SGL = 1). For SGL = 0, two
adjacent channels can be selected to form a differential
input; for SGL = 1, one of the 16 channels (CH0-CH15) is
selected as the positive input and the COM pin is used as
the negative input. For a given channel selection, the
converter will measure the voltage between the two chan-
nels indicated by IN+ and IN– in the selected row of Table 1.
Output Data Format
The LTC2439-1 serial output data stream is 19 bits long.
The first 3 bits represent status information indicating the
conversion state and sign. The next 16 bits are the conver-
sion result, MSB first. The third and fourth bit together are
also used to indicate an underrange condition (both bits low
means the differential input voltage is below –FS) or an
overrange condition (both bits high means the differential
input voltage is above +FS).
Bit 18 (first output bit) is the end of conversion (EOC)
indicator. This bit is available at the SDO pin during the
conversion and sleep states whenever the CS pin is LOW.
This bit is HIGH during the conversion and goes LOW
when the conversion is complete.
Bit 17 (second output bit) is a dummy bit (DMY) and is
always LOW.
Bit 16 (third output bit) is the conversion result sign indi-
cator (SIG). If VIN is >0, this bit is HIGH. If VIN is <0, this
bit is LOW.
Bit 15 (fourth output bit) is the most significant bit (MSB)
of the result. This bit in conjunction with Bit 16 also
provides the underrange or overrange indication. If both
Bit 16 and Bit 15 are HIGH, the differential input voltage is
above +FS. If both Bit 16 and Bit 15 are LOW, the
differential input voltage is below –FS.
The function of these bits is summarized in Table 2.
Table 2. LTC2439-1 Status Bits
Bit 18
Bit 17
Bit 16
Bit 15
Input Range
EOC
DMY
SIG
MSB
VIN ≥ 0.5 VREF
00
1
0V
≤ VIN < 0.5 VREF
00
1
0
–0.5 VREF ≤ VIN < 0V
0
1
VIN < – 0.5 VREF
00
0
Bits 15-0 are the 16-Bit conversion result MSB first.
Bit 0 is the least significant bit (LSB).
Data is shifted out of the SDO pin under control of the serial
clock (SCK), see Figure 3a. Whenever CS is HIGH, SDO
remains high impedance and any externally generated
SCK clock pulses are ignored by the internal data out shift
register.
In order to shift the conversion result out of the device, CS
must first be driven LOW. EOC is seen at the SDO pin of the
device once CS is pulled LOW. EOC changes real time from
HIGH to LOW at the completion of a conversion. This
signal may be used as an interrupt for an external micro-
controller. Bit 18 (EOC) can be captured on the first rising
edge of SCK. Bit 17 is shifted out of the device on the first
falling edge of SCK. The final data bit (Bit 0) is shifted out
on the falling edge of the 18th SCK and may be latched on
the rising edge of the 19th SCK pulse. On the falling edge
of the 19th SCK pulse, SDO goes HIGH indicating the
initiation of a new conversion cycle. This bit serves as EOC
APPLICATIO S I FOR ATIO
WU
UU
相关PDF资料 |
PDF描述 |
|---|---|
| PT02SE-24-61P | CONN RECEPT 61POS W/PINS CRIMP |
| VI-B7N-MW-S | CONVERTER MOD DC/DC 18.5V 100W |
| VE-B3T-IW-B1 | CONVERTER MOD DC/DC 6.5V 100W |
| LTC2439-1IGN | IC ADC 16BIT 16CH MCRPWR 28SSOP |
| VI-B7L-MW-S | CONVERTER MOD DC/DC 28V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2440CGN | 功能描述:IC ADC DIFFER 24-BIT HS 16-SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2440CGN#PBF | 功能描述:IC ADC DIFFER 24-BIT HS 16-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC2440CGN#PBF | 制造商:Linear Technology 功能描述:24BIT ADC DELTA SIG HS 16SSOP 制造商:Linear Technology 功能描述:24BIT ADC, DELTA SIG, HS, 16SSOP |
| LTC2440CGN#TR | 功能描述:IC CONV A/D 24-BIT DIFF 16-SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2440CGN#TRPBF | 功能描述:IC ADC DIFFER 24-BIT HS 16-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。