- 您现在的位置：买卖IC网 > PDF目录10687 > LTC2484IDD#PBF (Linear Technology)IC ADC 24BIT 10-DFN PDF资料下载
参数资料
| 型号： | LTC2484IDD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/42页 |
| 文件大小： | 0K |
| 描述： | IC ADC 24BIT 10-DFN |
| 标准包装： | 121 |
| 位数： | 24 |
| 采样率（每秒）： | 6.8 |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 480µW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-DFN（3x3） |
| 包装： | 管件 |
| 输入数目和类型： | 1 个差分，双极 |
| 产品目录页面： | 1348 (CN2011-ZH PDF) |
| 配用： | DC939A-ND - BOARD DELTA SIGMA ADC LTC2484 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
LTC2484
18
2484fd
APPLICATIONS INFORMATION
rst conversion result following POR is accurate within
the specications of the device if the power supply volt-
age is restored within the operating range (2.7V to 5.5V)
before the end of the POR time interval.
On-Chip Temperature Sensor
The LTC2484 contains an on-chip PTAT (proportional
to absolute temperature) signal that can be used as a
temperature sensor. The internal PTAT has a typical
value of 420mV at 27°C and is proportional to the abso-
lute temperature value with a temperature coefcient of
420/(27 + 273) = 1.40mV/°C (SLOPE), as shown in Figure 4.
The internal PTAT signal is used in a single-ended mode
referenced to device ground internally. The 1x speed mode
with automatic offset calibration is automatically selected
for the internal PTAT signal measurement as well.
to adjust the SLOPE value. The converter output of the
PTAT signal, R0SDO, is measured at a known temperature
T0 (in °C) and the SLOPE is calculated as:
SLOPE
=
R0SDO VREF
T0
+ 273
This calibrated SLOPE can be used to calculate the
temperature.
If the same VREF source is used during calibration and
temperature measurement, the actual value of the VREF
is not needed to measure the temperature as shown in
the calculation below:
TC =
RSDO VREF
SLOPE
– 273
=
RSDO
R0SDO
T0
+ 273
() – 273
Reference Voltage Range
The LTC2484 external reference voltage range is 0.1V
to VCC. The converter output noise is determined by the
thermal noise of the front-end circuits, and as such, its
value in nanovolts is nearly constant with reference voltage.
A reduced reference voltage will improve the converter
performance when operated with an external conversion
clock (external fO signal) at substantially higher output
data rates (see the Output Data Rate section). VREF must
be ≥1.1V to use the internal temperature sensor.
The negative reference input to the converter is internally
tied to GND. GND (Pin 8) should be connected to a ground
plane through as short a trace as possible to minimize
voltage drop. The LTC2484 has an average operational
current of 160μA and for 0.1Ω parasitic resistance, the
voltage drop of 16μV causes a gain error of 3.2ppm for
VREF = 5V.
Input Voltage Range
The analog input is truly differential with an absolute/com-
mon mode range for the IN+ and IN– input pins extending
from GND – 0.3V to VCC+0.3V.Outsidetheselimits,theESD
protection devices begin to turn on and the errors due to
input leakage current increase rapidly. Within these limits,
the LTC2484 converts the bipolar differential input signal,
TEMPERATURE (°C)
–60
V
PTAT
(mV)
500
600
120
2484 F04
400
200
30
090
–30
60
300
VCC = 5V
IM = 1
fO = GND
SLOPE = 1.40mV/°C
Figure 4. Internal PTAT Signal vs Temperature
When using the internal temperature sensor, if the output
code is normalized to RSDO = VPTAT/VREF, the temperature
is calculated using the following formula:
TK =
RSDO VREF
SLOPE
in Kelvin
and
TC =
RSDO VREF
SLOPE
–273 in
°C
where SLOPE is nominally 1.4mV/°C
Since the PTAT signal can have an initial value variation
which results in errors in SLOPE, to achieve better tem-
perature measurements, a one-time calibration is needed
相关PDF资料 |
PDF描述 |
|---|---|
| LTC2485IDD#PBF | IC ADC 24BIT I2C 10-DFN |
| LTC1443CDHD#TRPBF | IC COMP W/REF LOW PWR QUAD 16DFN |
| LTC1444CDHD#TRPBF | IC COMP QD LP 1.221VREF 16-DFN |
| AD9200ARSZ | IC ADC 10BIT CMOS 20MSPS 28-SSOP |
| LTC1445CDHD#TRPBF | IC COMP QD LP 1.221VREF 16-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2485CDD#PBF | 功能描述:IC ADC 24BIT I2C 10-DFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC2485CDD#TRPBF | 功能描述:IC ADC 24BIT I2C 10-DFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:12 采样率（每秒）:3M 数据接口:- 转换器数目:- 功率耗散（最大）:- 电压电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-23-6 包装:带卷 (TR) 输入数目和类型:- |
| LTC2485IDD | 制造商:Linear Technology 功能描述:ADC Single Delta-Sigma 7.5sps 24-bit Serial 10-Pin DFN EP |
| LTC2485IDD#PBF | 功能描述:IC ADC 24BIT I2C 10-DFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC2485IDD#TRPBF | 功能描述:IC ADC 24BIT I2C 10-DFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
发布紧急采购，3分钟左右您将得到回复。