- 您现在的位置：买卖IC网 > PDF目录10688 > LTC2487IDE#PBF (Linear Technology)IC ADC 16BIT DELTA SIG 14-DFN PDF资料下载
参数资料
| 型号： | LTC2487IDE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 6/32页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT DELTA SIG 14-DFN |
| 标准包装： | 91 |
| 位数： | 16 |
| 采样率（每秒）： | 15 |
| 数据接口： | I²C，串行 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 800µW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-WFDFN 裸露焊盘 |
| 供应商设备封装： | 14-DFN-EP（4x3） |
| 包装： | 管件 |
| 输入数目和类型： | 4 个单端，双极；2 个差分，双极 |
| 产品目录页面： | 1348 (CN2011-ZH PDF) |
| 配用： | DC1010A-C-ND - BOARD DELTA SIGMA ADC LTC2487 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC2487
14
2487fd
I2C INTERFACE
The LTC2487 communicates through an I2C interface. The
I2C interface is a 2-wire, open-drain interface supporting
multiple devices and multiple masters on a single bus. The
connected devices can only pull the data line (SDA) low
and can never drive it high. SDA is required to be externally
connected to the supply through a pull-up resistor. When
the data line is not being driven, it is high. Data on the
I2C bus can be transferred at rates up to 100kbits/s in the
standard mode and up to 400kbits/s in the fast mode. The
VCC power should not be removed from the device when
the I2C bus is active to avoid loading the I2C bus lines
through the internal ESD protection diodes.
Each device on the I2C bus is recognized by a unique
address stored in that device and can operate either as a
transmitter or receiver, depending on the function of the
device. In addition to transmitters and receivers, devices
can also be considered as masters or slaves when perform-
ing data transfers. A master is the device which initiates a
data transfer on the bus and generates the clock signals
to permit that transfer. Devices addressed by the master
are considered a slave.
The LTC2487 can only be addressed as a slave. Once ad-
dressed, it can receive conguration bits (channel selec-
tion, rejection mode, speed mode, gain) or transmit the
last conversion result. The serial clock line, SCL, is always
an input to the LTC2487 and the serial data line SDA is
bidirectional. The device supports the standard mode and
the fast mode for data transfer speeds up to 400kbits/s.
Figure 2 shows the denition of the I2C timing.
The Start and Stop Conditions
A Start (S) condition is generated by transitioning SDA from
high to low while SCL is high. The bus is considered to be
busy after the Start condition. When the data transfer is
nished, a Stop (P) condition is generated by transitioning
SDA from low to high while SCL is high. The bus is free
after a Stop is generated. Start and Stop conditions are
always generated by the master.
When the bus is in use, it stays busy if a Repeated Start
(Sr) is generated instead of a Stop condition. The repeated
Start timing is functionally identical to the Start and is
used for writing and reading from the device before the
initiation of a new conversion.
Data Transferring
After the Start condition, the I2C bus is busy and data
transfer can begin between the master and the addressed
slave. Data is transferred over the bus in groups of nine
bits, one byte followed by one acknowledge (ACK) bit.
The master releases the SDA line during the ninth SCL
clock cycle. The slave device can issue an ACK by pulling
SDA low or issue a Not Acknowledge (NAK) by leaving
the SDA line high impedance (the external pull-up resistor
will hold the line high). Change of data only occurs while
the clock line (SCL) is low.
DATA FORMAT
After a Start condition, the master sends a 7-bit address
followed by a read/write (R/W) bit. The R/W bit is 1 for
a read request and 0 for a write request. If the 7-bit ad-
Figure 2. Denition of Timing for Fast/Standard Mode Devices on the I2C Bus
APPLICATIONS INFORMATION
SDA
SCL
SSr
P
S
tHD(SDA)
tHD(DAT)
tSU(STA)
tSU(STO)
tSU(DAT)
tLOW
tHD(SDA)
tSP
tBUF
tr
tf
tr
tf
tHIGH
2487 F02
相关PDF资料 |
PDF描述 |
|---|---|
| LT1711IMS8 | IC COMP R-RINOUT SINGLE 8-MSOP |
| LT1394CS8 | IC COMPARATOR LOW PWR 7NS 8-SOIC |
| LTC2435-1CGN#PBF | IC ADC DIFF I/REF 20BIT 16-SSOP |
| AD8611ARZ-REEL7 | IC COMP SGL 4NS ULTRFAST 8SOIC |
| AD7823YRZ | IC ADC 8BIT SRL 2.7/5.5V 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2488CDE#PBF | 功能描述:IC ADC 16BIT DELTA SIG 14-DFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC2488CDE#TRPBF | 功能描述:IC ADC 16BIT DELTA SIG 14-DFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2488IDE#PBF | 功能描述:IC ADC 16BIT DELTA SIG 14-DFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC2488IDE#TRPBF | 功能描述:IC ADC 16BIT DELTA SIG 14-DFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2489CDE#PBF | 功能描述:IC ADC 16BIT DELTA SIG 14-DFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
发布紧急采购，3分钟左右您将得到回复。