参数资料
| 型号： | LTC2494IUHF#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/38页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT W/PGA 38-QFN |
| 标准包装： | 2,500 |
| 位数： | 16 |
| 采样率（每秒）： | 15 |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 480µW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-WFQFN 裸露焊盘 |
| 供应商设备封装： | 38-QFN（5x7） |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 16 个单端，双极；8 个差分，双极 |
| 配用： | DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
LTC2494
2494fd
applications inForMation
INPUT DATA FORMAT
The LTC2494 serial input word is 16 bits long and contains
two distinct sets of data. The first set (SGL, ODD, A2, A1,
A0) is used to select the input channel. The second set of
data (IM, FA, FB, SPD, GS2, GS1, GS0) is used to select
the frequency rejection, speed mode (1x, 2x), temperature
measurement and gain.
After power-up, the device initiates an internal reset cycle
whichsetstheinputchanneltoCH0–CH1(IN+=CH0,IN–=
CH1),thefrequencyrejectiontosimultaneous50Hz/60Hz,
1xoutputrate(auto-calibrationenabled),andgain=1.The
firstconversionautomaticallybeginsatpower-upusingthis
default configuration. Once the conversion is complete, a
new word may be written into the device.
The first three bits shifted into the device consist of two
preamble bits and an enable bit. These bits are used to
enable the device configuration and input channel selec-
tion. Valid settings for these three bits are 000, 100 and
101. Other combinations should be avoided. If the first
three bits are 000 or 100, the following data is ignored
(don’t care) and the previously selected input channel and
configuration remain valid for the next conversion.
If the first three bits shifted into the device are 101, then
the next five bits select the input channel for the next
conversion cycle (see Table 3).
The first input bit following the 101 sequence (SGL) de-
termines if the input selection is differential (SGL = 0) or
single-ended(SGL=1).ForSGL=0,twoadjacentchannels
canbeselectedtoformadifferentialinput.ForSGL=1,one
of16channelsisselectedasthepositiveinput.Thenegative
inputisCOMforallsingle-endedoperations.Theremaining
4bits(ODD,A2,A1,A0)determinewhichchannel(s)is/are
selected and the polarity (for a differential input).
The next serial input bit immediately following the input
channel selection is the enable bit for the conversion
configuration (EN2). If this bit is set to 0, then the next
conversion is performed using the previously selected
converter configuration. This is useful in systems using
the same rejection/speed for all input channels and for
backwardcompatibilitywiththeLTC2418/LTC2414families
of delta-sigma ADCs.
The second set of configuration data can be loaded into the
device by setting EN2 = 1 (see Table 4). The first bit (IM)
is used to select the internal temperature sensor. If IM = 1,
the following conversion will be performed on the internal
temperaturesensorratherthantheselectedinputchannel.
The next 2 bits (FA and FB) are used to set the rejection
frequency. The next bit (SPD) is used to select either the
1x output rate if SPD = 0 (auto-calibration is enabled and
the offset is continuously calibrated and removed from
the final conversion result) or the 2x output rate if SPD
Table 2. LTC2494 Output Data Format
DIFFERENTIAL INPUT VOLTAGE
VIN*
BIT 23
EOC
BIT 22
DMY
BIT 21
SIG
BIT 20
MSB
BIT 19
BIT 18
BIT 17
…
BIT 4
BITS 3 TO 0
VIN* ≥ FS**
0
1
0
…
0
0000
FS** – 1LSB
0
1
0
1
…
1
0000
0.5 FS**
0
1
0
1
0
…
0
0000
0.5 FS** – 1LSB
0
1
0
1
…
1
0000
0
1/0***
0
…
0
0000
–1LSB
0
1
…
1
0000
–0.5 FS**
0
1
0
…
0
0000
–0.5 FS** – 1LSB
0
1
0
1
…
1
0000
–FS**
0
1
0
…
0
0000
VIN* < –FS**
0
1
…
1
0000
*The differential input voltage VIN = IN+ – IN–. **The full-scale voltage FS = 0.5 VREF/Gain.
***The sign bit changes state during the 0 output code when the device is operating in the 2x speed mode.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC2495CUHF#PBF | IC ADC 16BIT W/PGA 38-QFN |
| LTC2496IUHF#TRPBF | IC ADC 16BIT DELTA SIG 38-QFN |
| LTC2498IUHF#TRPBF | IC ADC 24BIT 16CH 38-QFN |
| LTC2600IUFD#PBF | IC DAC OCTAL R-R 16BIT 20-QFN |
| LTC2602IMS8#TRPBF | IC DAC 16BIT DUAL R-R VOUT 8MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2495CUHF | 制造商:Linear Technology 功能描述:ADC Single Delta-Sigma 15sps 16-bit Serial 38-Pin QFN EP |
| LTC2495CUHF#PBF | 功能描述:IC ADC 16BIT W/PGA 38-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2495CUHF#TRPBF | 功能描述:IC ADC 16BIT W/PGA 38-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2495IUHF#PBF | 功能描述:IC ADC 16BIT W/PGA 38-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC2495IUHF#TRPBF | 功能描述:IC ADC 16BIT W/PGA 38-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。