参数资料
| 型号： | LTC2498IUHF#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 6/38页 |
| 文件大小： | 0K |
| 描述： | IC ADC 24BIT 16CH 38-QFN |
| 标准包装： | 2,500 |
| 位数： | 24 |
| 采样率（每秒）： | 7.5 |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 转换器数目： | 1 |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-WFQFN 裸露焊盘 |
| 供应商设备封装： | 38-QFN（5x7） |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 16 个单端，双极；8 个差分，双极 |
| 配用： | DC1011A-A-ND - BOARD DELTA SIGMA ADC LTC2498 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
LTC2498
14
2498ff
applications inForMation
CONVERTER OPERATION
Converter Operation Cycle
The LTC2498 is a multi-channel, low power, delta-sigma
analog-to-digitalconverterwithaneasytouse4-wireinter-
face and automatic differential input current cancellation.
Its operation is made up of three states (See Figure 2).
The converter operating cycle begins with the conversion,
followed by the sleep state and ends with the data input/
output cycle. The 4-wire interface consists of serial data
output (SDO), serial clock (SCK), chip select (CS) and
serial data input (SDI).The interface, timing, operation
cycle, and data output format is compatible with Linear’s
entire family of ΔS converters.
Initially,atpower-up,theLTC2498performsaconversion.
Once the conversion is complete, the device enters the
sleep state. While in this sleep state, if CS in HIGH, power
consumption is reduced by two orders of magnitude. The
part remains in the sleep state as long as CS is HIGH. The
conversionresultisheldindefinitelyinastaticshiftregister
while the part is in the sleep state.
Once CS is pulled LOW, the device powers up, exits the
sleep mode, and enters the data input/output state. If CS
is brought HIGH before the first rising edge of SCK, the
device returns to the sleep state and the power is reduced.
If CS is brought HIGH after the first rising edge of SCK, the
data output cycle is aborted and a new conversion cycle
begins. The data output corresponds to the conversion
just completed. This result is shifted out on the serial data
output pin (SDO) under the control of the serial clock pin
(SCK). Data is updated on the falling edge of SCK allowing
theusertoreliablylatchdataontherisingedgeofSCK(See
Figure 3). The configuration data for the next conversion
is also loaded into the device at this time. Data is loaded
from the serial data input pin (SDI) on each rising edge
of SCK. The data input/output cycle is concluded once 32
bits are read out of the ADC or when CS is brought HIGH.
The device automatically initiates a new conversion and
the cycle repeats.
ThroughtimingcontroloftheCSandSCKpins,theLTC2498
offers several flexible modes of operation (internal or
external SCK and free-running conversion modes). These
various modes do not require programming and do not
disturbthecyclicoperationdescribedabove.Thesemodes
of operation are described in detail in the Serial Interface
Timing Modes section.
Ease of Use
The LTC2498 data output has no latency, filter settling
delay or redundant data associated with the conversion
cycle. There is a one-to-one correspondence between the
conversion and the output data. Therefore, multiplexing
multipleanaloginputsisstraightforward.Eachconversion,
immediately following a newly selected input or mode, is
valid and accurate to the full specifications of the device.
The LTC2498 automatically performs offset and full scale
calibration every conversion cycle independent of the
input channel selected. This calibration is transparent to
the user and has no effect with the operation cycle de-
scribed above. The advantage of continuous calibration
is extreme stability of offset and full-scale readings with
respect to time, supply voltage variation, input channel,
and temperature drift.
Easy Drive Input Current Cancellation
The LTC2498 combines a high precision delta-sigma ADC
with an automatic, differential, input current cancellation
frontend.Aproprietaryfrontendpassivesamplingnetwork
transparently removes the differential input current. This
Figure 2. LTC2498 State Transition Diagram
CONVERT
SLEEP
CHANNEL SELECT
CONFIGURATION SELECT
DATA OUTPUT
POWER UP
IN+= CH0, IN–= CH1
50/60Hz,1X
2498 F02
CS = LOW
AND
SCK
相关PDF资料 |
PDF描述 |
|---|---|
| LTC2600IUFD#PBF | IC DAC OCTAL R-R 16BIT 20-QFN |
| LTC2602IMS8#TRPBF | IC DAC 16BIT DUAL R-R VOUT 8MSOP |
| LTC2604IGN-1#TRPBF | IC DAC 16BIT QUAD R-R OUT 16SSOP |
| LTC2605IGN-1#TRPBF | IC DAC 16BIT OCT I2C 16-SSOP |
| LTC2606IDD#TRPBF | IC DAC 16BIT I2C V-OUT 10-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2499CUHF | 制造商:Linear Technology 功能描述:ADC Single Delta-Sigma 7.5sps 24-bit Serial 38-Pin QFN EP |
| LTC2499CUHF#PBF | 功能描述:IC ADC 24BIT DELTA SIG 38-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC2499CUHF#TRPBF | 功能描述:IC ADC 24BIT DELTA SIG 38-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2499CUHFPBF | 制造商:Linear Technology 功能描述:24bit Delta Sigma ADC Temp Sens LTC2499 |
| LTC2499IUHF#PBF | 功能描述:IC ADC 24BIT DELTA SIG 38-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
发布紧急采购，3分钟左右您将得到回复。