参数资料
| 型号： | LTC2619CGN#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/22页 |
| 文件大小： | 0K |
| 描述： | IC DAC 14BIT R-R QUAD 16SSOP |
| 标准包装： | 2,500 |
| 设置时间： | 9µs |
| 位数： | 14 |
| 数据接口： | 串行 |
| 转换器数目： | 4 |
| 电压电源： | 单电源 |
| 功率耗散（最大）： | 750µW |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 带卷 (TR) |
| 输出数目和类型： | 4 电压，单极 |
| 采样率（每秒）： | * |
LTC2609/LTC2619/LTC2629
26091929fb
operation
main bias generation circuit block has been automatically
shut down in addition to the individual DAC amplifiers and
reference inputs. In this case, the power-up delay time is
12s (for VCC = 5V) or 30s (for VCC = 3V).
Voltage Output
The rail-to-rail amplifier has guaranteed load regulation
when sourcing or sinking up to 15mA at 5V (7.5mA at
2.7V).
Load regulation is a measure of the amplifier’s ability to
maintain the rated voltage accuracy over a wide range of
load conditions. The measured change in output voltage
permilliampereofforcedloadcurrentchangeisexpressed
in LSB/mA.
DC output impedance is equivalent to load regulation, and
may be derived from it by simply calculating a change in
units from LSB/mA to Ohms. The amplifier’s DC output
impedance is 0.035Ω when driving a load well away from
the rails.
When drawing a load current from either rail, the output
voltage headroom with respect to that rail is limited by
the 30Ω typical channel resistance of the output devices;
e.g., when sinking 1mA, the minimum output voltage =
30Ω 1mA = 30mV. See the graph Headroom at Rails vs
Output Current in the Typical Performance Characteristics
section.
The amplifier is stable driving capacitive loads of up to
1000pF.
Board Layout
TheexcellentloadregulationandDCcrosstalkperformance
of these devices is achieved in part by keeping “signal”
and “power” grounds separate.
The PC board should have separate areas for the analog
and digital sections of the circuit. This keeps digital signals
away from sensitive analog signals and facilitates the use
of separate digital and analog ground planes which have
minimal capacitive and resistive interaction with each
other.
Digital and analog ground planes should be joined at only
one point, establishing a system star ground as close to
the device’s ground pin as possible. Ideally, the analog
ground plane should be located on the component side of
the board, and should be allowed to run under the part to
shielditfromnoise.Analoggroundshouldbeacontinuous
and uninterrupted plane, except for necessary lead pads
and vias, with signal traces on another layer.
The GND pin functions as a return path for power supply
currents in the device and should be connected to analog
ground.ResistancefromtheGNDpintosystemstarground
should be as low as possible. When a zero-scale DAC
output voltage of zero is desired, REFLO (Pin 2) should
be connected to system star ground.
Rail-to-Rail Output Considerations
Inanyrail-to-railvoltageoutputdevice,theoutputislimited
to voltages within the supply range.
Since the analog output of the device cannot go below
ground, it may limit for the lowest codes as shown in
Figure4b.Similarly,limitingcanoccurnearfull-scalewhen
the REF pins are tied to VCC. If REFx = VCC and the DAC
full-scale error (FSE) is positive, the output for the highest
codes limits at VCC as shown in Figure 4c. No full-scale
limiting can occur if REFx is less than VCC – FSE.
Offset and linearity are defined and tested over the region
of the DAC transfer function where no output limiting can
occur.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1454LIN | IC DAC 12BIT R-R DUAL 3V 16DIP |
| AD7545AKPZ-REEL | IC DAC 12BIT W/BUFF MULT 20PLCC |
| LTC1446LIS8#TR | IC DAC 12BIT DUAL R-R MPWR 8SOIC |
| AD5422BREZ-REEL | IC DAC 16BIT 1CH SRL INP 24TSSOP |
| AD5045BRUZ-REEL7 | IC DAC DUAL 14BIT SPI 14TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2619IGN#PBF | 功能描述:IC DAC 14BIT R-R QUAD 16SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
| LTC2619IGN#TRPBF | 功能描述:IC DAC 14BIT R-R QUAD 16SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:2,400 系列:- 设置时间:- 位数:18 数据接口:串行 转换器数目:3 电压电源:模拟和数字 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:36-TFBGA 供应商设备封装:36-TFBGA 包装:带卷 (TR) 输出数目和类型:* 采样率（每秒）:* |
| LTC2619IGN-1#PBF | 功能描述:IC DAC 14BIT R-R QUAD 16SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:47 系列:- 设置时间:2µs 位数:14 数据接口:并联 转换器数目:1 电压电源:单电源 功率耗散（最大）:55µW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SSOP（0.209"，5.30mm 宽） 供应商设备封装:28-SSOP 包装:管件 输出数目和类型:1 电流，单极；1 电流，双极 采样率（每秒）:* |
| LTC2619IGN-1#TRPBF | 功能描述:IC DAC 14BIT R-R QUAD 16SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:2,400 系列:- 设置时间:- 位数:18 数据接口:串行 转换器数目:3 电压电源:模拟和数字 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:36-TFBGA 供应商设备封装:36-TFBGA 包装:带卷 (TR) 输出数目和类型:* 采样率（每秒）:* |
| LTC2620CGN | 功能描述:IC DAC OCTAL R-R 12BIT 16SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:47 系列:- 设置时间:2µs 位数:14 数据接口:并联 转换器数目:1 电压电源:单电源 功率耗散（最大）:55µW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SSOP（0.209"，5.30mm 宽） 供应商设备封装:28-SSOP 包装:管件 输出数目和类型:1 电流，单极；1 电流，双极 采样率（每秒）:* |
发布紧急采购，3分钟左右您将得到回复。