参数资料
| 型号： | LTC2620CGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 4/20页 |
| 文件大小： | 0K |
| 描述： | IC DAC OCTAL R-R 12BIT 16SSOP |
| 标准包装： | 100 |
| 设置时间： | 70µs |
| 位数： | 12 |
| 数据接口： | 串行 |
| 转换器数目： | 8 |
| 电压电源： | 单电源 |
| 功率耗散（最大）： | 20mW |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 管件 |
| 输出数目和类型： | 8 电压，单极 |
| 采样率（每秒）： | * |
| 产品目录页面： | 1351 (CN2011-ZH PDF) |
LTC2600/LTC2610/LTC2620
12
2600fe
OPERATION
Power-On Reset
The LTC2600/LTC2610/LTC2620 clear the outputs to
zero-scale when power is rst applied, making system
initialization consistent and repeatable.
Forsomeapplications,downstreamcircuitsareactiveduring
DAC power-up, and may be sensitive to nonzero outputs
from the DAC during this time. The LTC2600/2610/2620
contain circuitry to reduce the power-on glitch: the analog
outputs typically rise less than 10mV above zero-scale
during power on if the power supply is ramped to 5V in 1ms
or more. In general, the glitch amplitude decreases as the
power supply ramp time is increased. See Power-On Reset
Glitch in the Typical Performance Characteristics section.
Power Supply Sequencing
The voltage at REF (Pin 6) should be kept within the
range –0.3V ≤ VREF ≤ VCC + 0.3V (see Absolute Maximum
Ratings). Particular care should be taken to observe these
limits during power supply turn-on and turn-off sequences,
when the voltage at VCC (Pin 16) is in transition.
Transfer Function
The digital-to-analog transfer function is:
V
k
V
OUT IDEAL
N
REF
() =
2
where k is the decimal equivalent of the binary DAC
input code, N is the resolution and VREF is the voltage at
REF (Pin 6).
Serial Interface
The CS/LD input is level triggered. When this input is taken
low, it acts as a chip-select signal, powering on the SDI and
SCK buffers and enabling the input shift register. Data (SDI
input) is transferred at the next 24 rising SCK edges. The
4-bit command, C3-C0, is loaded rst; then the 4-bit DAC
address, A3-A0; and nally the 16-bit data word. The data
word comprises the 16-, 14- or 12-bit input code, ordered
MSB-to-LSB, followed by 0, 2 or 4 don’t-care bits (LTC2600,
LTC2610 and LTC2620 respectively). Data can only be
transferred to the device when the CS/LD signal is low.The
rising edge of CS/LD ends the data transfer and causes the
device to carry out the action specied in the 24-bit input
word. The complete sequence is shown in Figure 2a.
The command (C3-C0) and address (A3-A0) assignments
are shown in Table 1. The rst four commands in the table
consist of write and update operations. A write operation
loads a 16-bit data word from the 32-bit shift register
into the input register of the selected DAC, n. An update
operation copies the data word from the input register to
the DAC register. Once copied into the DAC register, the
data word becomes the active 16-, 14- or 12-bit input
code, and is converted to an analog voltage at the DAC
output. The update operation also powers up the selected
DAC if it had been in power-down mode. The data path
and registers are shown in the Block Diagram.
While the minimum input word is 24 bits, it may optionally
be extended to 32 bits. To use the 32-bit word width, 8
don’t-care bits are transferred to the device rst, followed
by the 24-bit word as just described. Figure 2b shows the
Table 1.
COMMAND*
C3
C2
C1
C0
0000
Write to Input Register n
0001
Update (Power Up) DAC Register n
0010
Write to Input Register n, Update (Power Up) All n
0011
Write to and Update (Power Up) n
0100
Power Down n
1111
No Operation
*Command and address codes not shown are reserved and should not be used.
ADDRESS (n)*
A3
A2
A1
A0
0000
DAC A
0001
DAC B
0010
DAC C
0011
DAC D
0100
DAC E
0101
DAC F
0110
DAC G
0111
DAC H
1111
All DACs
相关PDF资料 |
PDF描述 |
|---|---|
| SI5338B-A-GM | IC CLK GEN QUAD 350MHZ 24-QFN |
| MS3450W28-21SY | CONN RCPT 37POS WALL MNT W/SCKT |
| MS3450W28-21SX | CONN RCPT 37POS WALL MNT W/SCKT |
| LTC2641IS8-16#PBF | IC DAC 16BIT VOUT 8-SOIC |
| MS3450W28-21SW | CONN RCPT 37POS WALL MNT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2620CUFD#PBF | 功能描述:IC DAC OCTAL R-R 12BIT 20-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 设置时间:4µs 位数:12 数据接口:串行 转换器数目:2 电压电源:单电源 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-uMAX 包装:管件 输出数目和类型:2 电压，单极 采样率（每秒）:* 产品目录页面:1398 (CN2011-ZH PDF) |
| LTC2620CUFD#PBF | 制造商:Linear Technology 功能描述:D/A Converter IC |
| LTC2620CUFD#TRPBF | 功能描述:IC DAC OCTAL R-R 12BIT 20-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:47 系列:- 设置时间:2µs 位数:14 数据接口:并联 转换器数目:1 电压电源:单电源 功率耗散（最大）:55µW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SSOP（0.209"，5.30mm 宽） 供应商设备封装:28-SSOP 包装:管件 输出数目和类型:1 电流，单极；1 电流，双极 采样率（每秒）:* |
| LTC2620IGN | 功能描述:IC DAC 12BIT OCTAL R-R 16SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:47 系列:- 设置时间:2µs 位数:14 数据接口:并联 转换器数目:1 电压电源:单电源 功率耗散（最大）:55µW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SSOP（0.209"，5.30mm 宽） 供应商设备封装:28-SSOP 包装:管件 输出数目和类型:1 电流，单极；1 电流，双极 采样率（每秒）:* |
| LTC2620IGN#PBF | 功能描述:IC DAC OCTAL R-R 12BIT 16SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:1 系列:- 设置时间:4.5µs 位数:12 数据接口:串行，SPI? 转换器数目:1 电压电源:单电源 功率耗散（最大）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOICN 包装:剪切带 (CT) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:* 其它名称:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
发布紧急采购，3分钟左右您将得到回复。