- 您现在的位置：买卖IC网 > PDF目录8577 > LTC2754BIUKG-16#TRPBF (Linear Technology)IC DAC 16BIT QUAD IOUT 52-QFN PDF资料下载
参数资料
| 型号： | LTC2754BIUKG-16#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 5/28页 |
| 文件大小： | 0K |
| 描述： | IC DAC 16BIT QUAD IOUT 52-QFN |
| 标准包装： | 2,000 |
| 系列： | SoftSpan™ |
| 设置时间： | 2µs |
| 位数： | 16 |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 4 |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 52-WFQFN 裸露焊盘 |
| 供应商设备封装： | 52-QFN（7x8）裸露焊盘 |
| 包装： | 带卷 (TR) |
| 输出数目和类型： | 8 电流，单极；8 电流，双极 |
| 采样率（每秒）： | * |
| 配用： | DC1546A-ND - BOARD DAC LTC2754-16 |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC2754
13
2754f
Input and DAC Registers
The LTC2754 has 5 internal registers for each DAC, a total
of 20 registers (see Block Diagram). Each DAC channel
has two sets of double-buffered registers—one set for the
code data, and one for the output range of the DAC—plus
one readback register. Double buffering provides the ca-
pability to simultaneously update the span (output range)
and code, which allows smooth voltage transitions when
changing output ranges. It also permits the simultaneous
updating of multiple DACs.
Each set of double-buffered registers comprises an Input
register and a DAC register.
Input register: The Write operation shifts data from the
SDI pin into a chosen Input register. The Input registers
are holding buffers; Write operations do not affect the
DAC outputs.
DAC register: The Update operation copies the contents
of an Input register to its associated DAC register. The
contents of a DAC register directly updates the associated
DAC output voltage or output range.
Note that updates always include both Data and Span
registers; but the values held in the DAC registers will
only change if the associated Input register values have
previously been changed via a Write operation.
Serial Interface
When the CS/LD pin is taken low, the data on the SDI
pin is loaded into the shift register on the rising edge of
the clock (SCK pin). The minimum (24-bit wide) loading
sequence required for the LTC2754 is a 4-bit command
word (C3 C2 C1 C0), followed by a 4-bit address word
(A3 A2 A1 A0) and 16 data (span or code) bits, MSB rst.
Figure 2 shows the SDI input word syntax to use when
writing code or span. If a 32-bit input sequence is used,
the rst eight bits must be zeros, followed by the same
sequence as for a 24-bit wide input. Figure 3 shows the
input and readback sequences for both 24-bit and 32-bit
operations.
When CS/LD is low, the SRO pin (Serial Readback Output)
is an active output.The readback data begins after the
command (C3-C0) and address (A3-A0) words have been
shifted into SDI. SRO outputs a logic low until the readback
OPERATION
data begins. For a 24-bit input sequence, the 16 readback
bits are shifted out on the falling edges of clocks 8-23,
suitable for shifting into a microprocessor on the rising
edges of clocks 9-24. For a 32-bit sequence, the bits are
shifted out on clocks 16-31; see Figure 3b.
When CS/LD is high, the SRO pin presents a high impedance
(three-state) output.
LDAC is an asynchronous update pin. When LDAC is
taken low, all DACs are updated with code and span data
(data in the Input buffers is copied into the DAC buffers).
CS/LD must be high during this operation; otherwise
LDAC is locked out and will have no effect. The use of
LDAC is functionally identical to the “Update All DACs”
serial input command.
The codes for the command word (C3-C0) are dened in
Table 1; Table 2 denes the codes for the address word
(A3-A0).
Readback
In addition to the Input and DAC registers, each DAC has
one Readback register associated with it. When a Read
command is issued to a DAC, the contents of one of its
four buffers (Input and DAC registers for each of Span
and Code) is copied into its Readback register and seri-
ally shifted out through the SRO pin. Figure 3 shows the
loading and readback sequences.
In the data eld (D15-D0) of any non-read instruction cycle,
SRO shifts out the contents of the buffer that was specied
in the preceding command. This “rolling readback” default
mode of operation can dramatically reduce the number
of instruction cycles needed, since any command can be
veried during succeeding commands with no additional
overhead. See Figure 4. Table 1 shows the storage location
(‘readback pointer’) of the data which will be output from
SRO during the next instruction.
For Read commands, the data is shifted out during the Read
instruction itself (on the 16 falling SCK edges immediately
after the last address bit is shifted in on SDI). When checking
the span of a DAC using SRO, the span bits are the last
four bits shifted out, corresponding to their sequence and
positions when writing a span. See Figure 3.
相关PDF资料 |
PDF描述 |
|---|---|
| HA3-5020-5Z | IC AMP VIDEO CFA 100MHZ 8-DIP |
| HFA1105IBZ | IC OPAMP CFA 330MHZ LP 8-SOIC |
| VI-B1N-MU | CONVERTER MOD DC/DC 18.5V 200W |
| HA9P5020-5Z | IC AMP VIDEO 100MHZ CFB 8-SOIC |
| AD7226KN | IC DAC 8BIT LC2MOS QUAD 20-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2754CUKG-12#PBF | 功能描述:IC DAC 12BIT QUAD IOUT 52-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:SoftSpan™ 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
| LTC2754CUKG-12#TRPBF | 功能描述:IC DAC 12BIT QUAD IOUT 52-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:SoftSpan™ 标准包装:47 系列:- 设置时间:2µs 位数:14 数据接口:并联 转换器数目:1 电压电源:单电源 功率耗散（最大）:55µW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SSOP（0.209"，5.30mm 宽） 供应商设备封装:28-SSOP 包装:管件 输出数目和类型:1 电流，单极；1 电流，双极 采样率（每秒）:* |
| LTC2754IUKG-12#PBF | 功能描述:IC DAC 12BIT QUAD IOUT 52-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:SoftSpan™ 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
| LTC2754IUKG-12#TRPBF | 功能描述:IC DAC 12BIT QUAD IOUT 52-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:SoftSpan™ 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
| LTC2755ACUP-16#PBF | 功能描述:IC DAC 16BIT CUR OUT 64-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:SoftSpan™ 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
发布紧急采购，3分钟左右您将得到回复。