- 您现在的位置：买卖IC网 > PDF目录10784 > LTC2846IG#PBF (Linear Technology)IC TXRX 3.3V MULTIPROTCOL 36SSOP PDF资料下载
参数资料
| 型号： | LTC2846IG#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/24页 |
| 文件大小： | 0K |
| 描述： | IC TXRX 3.3V MULTIPROTCOL 36SSOP |
| 标准包装： | 37 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 3/3 |
| 规程： | 多协议 |
| 电源电压： | 3.3V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 36-SSOP |
| 包装： | 管件 |
17
LTC2846
sn2846 2846fs
A port with one DB-25 connector, that can be configured
for either DTE or DCE operation is shown in Figure 33. The
configuration requires separate cables for proper signal
routing in DTE or DCE operation. For example, in DTE
mode, the TXD signal is routed to Pins 2 and 14 via the
LTC2846’s Driver 1. In DCE mode, Driver 1 now routes the
RXD signal to Pins 2 and 14.
Multiprotocol Interface with RL, LL, TM
and a DB-25 Connector
If the RL, LL and TM signals are implemented, there are not
enough drivers and receivers available in the LTC2846/
LTC2844. In Figure 34, the required control signals are
handled by the LTC2845. The LTC2845 has an additional
single-ended driver/receiver pair that can handle two more
optional control signals such as TM and RL.
Cable-Selectable Multiprotocol Interface
A cable-selectable multiprotocol DTE/DCE interface is
shown in Figure 35. The select lines M0, M1 and DCE/DTE
are brought out to the connector. The mode is selected by
the cable by wiring M0 (connector Pin 18) and M1 (con-
nector Pin 21) and DCE/DTE (connector Pin 25) to ground
(connector Pin 7) or letting them float. If M0, M1 or
DCE/DTE is floating, internal pull-up current sources will
pull the signals to VIN. The select bit M2 is floating, and
therefore, internally pulled high. When the cable is pulled
out, the interface will go into the no-cable mode.
Power Dissipation Calculations
The LTC2846 takes in a 3.3V supply and produces a 5V VCC
with an internal switcher at approximately 80% efficiency.
VDD and VEE are in turn produced from VCC with an internal
charge pump at approximately 80% and 70% efficiency
respectively. Current drawn internally from VDD or VEE
translates directly into a higher ICC. The LTC2846 dissi-
pates power according to the equation:
PDISS(2846) = 125% (VCC ICC)
– ND PRT + NR PRT
(1)
TYPICAL APPLICATIO S
U
PRT refers to the power dissipated by each driver in a
receiver termination on the far end of the cable while ND is
the number of drivers. Conversely, current from the far
end drivers dissipate power NR PRT in the internal
receiver termination where NR is the number of receivers.
LTC2846 Power Dissipation
Consider an LTC2846 in X.21, DCE mode (three V.11
drivers and two V.11 receivers). From the Electrical Char-
acteristics Table, ICC at no load = 14mA, ICC at full load =
100mA. Each receiver termination is 100
(RRT) and
current going into each receiver termination = (100mA –
14mA)/3 = 28.7mA (IRT).
PRT = (IRT)2 RRT
(2)
From Equation (2), PRT = 82.4mW and from Equation (1),
DC power dissipation PDISS(2846) = 125% (5V 100mA)
– 3 82.4mW + 2 82.4mW = 543mW.
Consider the above example running at a baud rate of
10MBd. From the Typical Characteristic for “V.11 Mode
ICC vs Data Rate,” the ICC at 10MBd is 160mA. ICC
increases with baud rate due to driver transient dissipa-
tion. From Equation (1), AC power dissipation PDISS(2846)
= 125% (5V 160mA) –3 82.4mW + 2 82.4mW =
918mW.
LTC2845 Power Dissipation
If a LTC2845 is used to form a complete DCE port with the
LTC2846, it will be running in the X.21 mode (three V.11
drivers and two V.10 drivers, two V.11 receivers and two
V.10 receivers, all with internal 30k termination). In addi-
tion to VCC, it uses the VDD and VEE outputs from the
LTC2846. Negligible power is dissipated in the large
internal receiver termination of the LTC2845 so the NR
PRT term of Equation (1) can be omitted. Thus Equation (1)
is modified as follows:
PDISS(2845) = (VCC ICC) + (VDD IDD)
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JTY-MW-S | CONVERTER MOD DC/DC 3.3V 66W |
| VI-BNW-MW | CONVERTER MOD DC/DC 5.5V 100W |
| AD7225KRZ-REEL | IC DAC 8BIT QUAD W/AMP 24SOIC |
| LTC1343IGW#PBF | IC TXRX SOFTWARE-SELECTBL 44SSOP |
| VI-JTX-MY-S | CONVERTER MOD DC/DC 5.2V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2847CUHF | 功能描述:IC TXRX MULTIPROTOCOL 38-QFN RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| LTC2847CUHF#PBF | 功能描述:IC TXRX MULTIPROTOCOL 38-QFN RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1 系列:- 类型:线路收发器 驱动器/接收器数:5/3 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC 包装:Digi-Reel® 产品目录页面:918 (CN2011-ZH PDF) 其它名称:296-25096-6 |
| LTC2847CUHF#TR | 功能描述:IC TXRX MULTIPROTOCOL 38-QFN RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| LTC2847CUHF#TRPBF | 功能描述:IC TXRX MULTIPROTOCOL 38-QFN RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| LTC2847IUHF | 功能描述:IC TXRX MULTIPROTOCOL 38-QFN RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。