- 您现在的位置：买卖IC网 > PDF目录15357 > LTC2901-2IGN#TR (Linear Technology)IC MONITOR SUPPLY QUAD 16-SSOP PDF资料下载
参数资料
| 型号： | LTC2901-2IGN#TR |
| 厂商： | Linear Technology |
| 文件页数： | 8/16页 |
| 文件大小： | 0K |
| 描述： | IC MONITOR SUPPLY QUAD 16-SSOP |
| 标准包装： | 2,500 |
| 类型： | 多压监控器 |
| 监视电压数目： | 4 |
| 输出： | 推挽式，图腾柱 |
| 复位： | 低有效 |
| 复位超时： | 最小为 5 ms |
| 电压 - 阀值： | 16 种可选阀值组合 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 带卷 (TR) |
LTC2901
PI FU CTIO S
COMP3 (Pin 1): Comparator Output 3. Nondelayed, active
high logic output with weak pull-up to V2. Pulls high when
V3 is above reset threshold. May be pulled greater than V2
using external pull-up.
COMP1 (Pin 2): Comparator Output 1. Nondelayed, active
high logic output with weak pull-up to V2. Pulls high when
V1 is above reset threshold. May be pulled greater than V2
using external pull-up.
V3 (Pin 3): Voltage Input 3. Select from 2.5V, 1.8V, 1.5V
or ADJ. See Table 1 for details.
V1 (Pin 4): Voltage Input 1. Select from 5V or 3.3V. See
Table 1 for details. The greater of (V1, V2) is also V CC for
the device. Bypass this pin to ground with a 0.1 μ F (or
greater) capacitor.
CRT (Pin 5): Reset Delay Time Programming Pin. Attach
an external capacitor (C RT ) to GND to set a reset delay time
of 4.6ms/nF. Leaving the pin open generates a minimum
delay of approximately 50 μ s. A 47nF capacitor will gener-
ate a 216ms reset delay time.
RST (Pin 6): Reset Logic Output. Active low with weak
pull-up to V2 (LTC2901-1/LTC2901-3) or active pull-up to
V2 (LTC2901-2/LTC2901-4). Pulls low when any voltage
input is below the reset threshold and held low for the
programmed delay time after all voltage inputs are above
threshold. May be pulled above V2 using an external pull-
up (LTC2901-1/LTC2901-3 only).
WDO (Pin 7): LTC2901-1/LTC2901-2 Watchdog Output.
Active low logic output with weak pull-up to V2. May be
pulled greater than V2 using external pull-up. The watch-
dog output pulls low if the watchdog timer is allowed to
time out and remains low until set high by the next WDI
transistion or anytime RST is low. The watchdog timer is
enabled when RST is high.
T0L (Pin 7): LTC2901-3/LTC2901-4 Digital Input for Sup-
ply Tolerance Selection (5% or 10%). A logic low selects
5% thresholds; a logic high selects 10% thresholds.
WDI (Pin 8): Watchdog Input. A logic input whose rising
or falling edge must occur on this pin (while RST is high)
within the selected watchdog time-out period, prohibiting
a high-to-low transition on the WDO pin (LTC2901-1/
LTC2901-2). The watchdog time-out period is set by the
value of the capacitor that is attached to the CWT pin.
A rising or falling edge on the WDI pin clears the voltage
on the C WT capacitor, preventing WDO from going low.
When disabling the watchdog function, tie CWT to GND.
For the LTC2901-3/LTC2901-4, a watchdog time-out due
to a missed WDI edge issues an RST pulse on the RST pin
(the WDO function is merged into the RST function).
CWT (Pin 9): Watchdog Time-Out Programming Pin.
Attach a capacitor (C WT ) between CWT and GND to set a
watchdog time-out period of 20ms/nF. Leaving the pin
open generates a minimum time-out of approximately
200 μ s. A 47nF capacitor will generate a 940ms watchdog
time-out period.
GND (Pin 10): Ground.
V PG (Pin 11): Voltage Threshold Combination Select In-
put. Connect to an external 1% resistive divider between
V REF and GND to select 1 of 16 combinations of preset and/
or ± adjustable voltage thresholds (see Table 1). Do not
add capacitance on the V PG pin.
V REF (Pin 12): Buffered Reference Voltage. A 1.210V
nominal reference used for programming voltage (V PG )
and for the offset of negative adjustable applications. The
buffered reference can source and sink up to 1mA. The
reference can drive a bypass capacitor of up to 1000pF
without oscillation.
V4 (Pin 13): Voltage Input 4. Select from 1.8V, 1.5V, ADJ
or – ADJ. See Table 1 for details.
V2 (Pin 14): Voltage Input 2. Select from 3.3V, 3V or 2.5V.
See Table 1 for details. The greater of (V1, V2) is also V CC
for device. Bypass this pin to ground with a 0.1 μ F (or
greater) capacitor. All logic outputs (COMP1, COMP2,
COMP3, COMP4, RST, WDO) are weakly pulled up to V2
(LTC2901-1/LTC2901-3). RST is actively pulled up to V2
in the LTC2901-2/LTC2901-4.
COMP4 (Pin 15): Comparator Output 4. Nondelayed,
active high logic output with weak pull-up to V2. Pulls high
when V4 is above reset threshold. May be pulled greater
than V2 using external pull-up.
COMP2 (Pin 16): Comparator Output 2. Nondelayed,
active high logic output with weak pull-up to V2. Pulls high
when V2 is above reset threshold. May be pulled greater
than V2 using external pull-up.
2901fb
8
相关PDF资料 |
PDF描述 |
|---|---|
| DLFL-0125-0501 | DLFL SATURATION CHOKE 5A |
| LTC2919IMS-3.3#TRPBF | IC MONITOR PREC 3.3V 10-MSOP |
| LTC2919IMS-2.5#TRPBF | IC MONITOR PREC 2.5V 10-MSOP |
| LTC2901-3IGN#PBF | IC MONITOR QUAD SUPP PROG 16SSOP |
| ESRL560M0ER | CAP ALUM 56UF 2.5V 20% SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2901-3CGN | 功能描述:IC MONITOR QUAD SUPP PROG 16SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC2901-3CGN#PBF | 功能描述:IC MONITOR QUAD SUPP PROG 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC2901-3CGN#TR | 功能描述:IC MONITOR QUAD SUPP PROG 16SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC2901-3CGN#TRPBF | 功能描述:IC MONITOR QUAD SUPP PROG 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC2901-3IGN | 功能描述:IC MONITOR QUAD SUPP PROG 16SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
发布紧急采购，3分钟左右您将得到回复。