- 您现在的位置：买卖IC网 > PDF目录15358 > LTC2901-4IGN#PBF (Linear Technology)IC MONITOR QUAD SUPP PROG 16SSOP PDF资料下载
参数资料
| 型号： | LTC2901-4IGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/16页 |
| 文件大小： | 0K |
| 描述： | IC MONITOR QUAD SUPP PROG 16SSOP |
| 标准包装： | 100 |
| 类型： | 多压监控器 |
| 监视电压数目： | 4 |
| 输出： | 推挽式，图腾柱 |
| 复位： | 低有效 |
| 复位超时： | 最小为 5 ms |
| 电压 - 阀值： | 16 种可选阀值组合 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 管件 |
LTC2901
APPLICATIO S I FOR ATIO
R PU =
Ω
Pull-Up Current vs V2 curve). Output rise time (10% to
90%) is estimated using:
t RISE ≈ 2.2 ? R PU ? C LOAD
where R PU is the on-resistance of the pull-up transistor.
The on-resistance as a function of the V2 voltage at room
temperature is estimated using:
6 ? 10 5
V 2 – 1
with V2 = 3.3V, R PU is about 260k. Using 150pF for load
capacitance, the rise time is 86 μ s. If the output needs to
pull up faster and/or to a higher voltage, a smaller
external pull-up resistor may be used. Using a 10k pull-
up resistor, the rise time is reduced to 3.3 μ s for a 150pF
load capacitance.
The LTC2901-2 has an active pull-up to V2 on the RST
output. The typical performance curve (RST Pull-Up Cur-
rent vs V2 curve) demonstrates that the pull-up current is
somewhat linear versus the V2 voltage and R PU is esti-
mated to be approximately 625 Ω . A 150pF load capaci-
tance makes the rise time about 206ns.
Watchdog Timer
The watchdog circuit typically monitors a μ P’s activity. The
μ P is required to change the logic state of the WDI pin on
a periodic basis in order to clear the watchdog timer and
prevent the WDO pin (LTC2901-1/LTC2901-2) from going
low. Whenever RST is low, the watchdog timer is cleared
and WDO is set high. The watchdog timer is started when
RST pulls high. Subsequent edges received on the WDI pin
will clear the watchdog timer. The timer will continue to
run until the watchdog timer times out. Once the watchdog
timer times out, internal circuitry will bring the WDO pin
low. WDO will remain low and the watchdog timer will
remain cleared until the next edge is received on the WDI
pin or until RST goes low.
In the LTC2901-3/LTC2901-4, there is no WDO pin. Instead,
the RST pin is pulled low for the programmed reset time-
out period whenever a WDI edge is missed. In this manner,
a full system reset can be issued after a watchdog failure.
To disable the watchdog timer, simply ground the CWT pin
(Pin 9). With CWT held at ground, any reset event will force
WDO high indefinitely. It is safe to leave the WDI pin
(Pin 8) unconnected because the weak internal pull-up
(10 μ A typ) will pull WDI high. Tying WDI to V1 or ground
is also allowed, but grounding the WDI pin will force the
pull-up current to be drawn continuously.
Selecting the Reset Timing Capacitor
The reset time-out period is adjustable in order to accom-
modate a variety of microprocessor applications. The
reset time-out period, t RST , is adjusted by connecting a
capacitor, C RT , between the CRT pin and ground. The
value of this capacitor is determined by:
C RT = t RST ? 217 ? 10 –9
with C RT in Farads and t RST in seconds. The C RT value per
millisecond of delay can also be expressed as C RT /ms =
217 (pF/ms).
Leaving the CRT pin unconnected will generate a mini-
mum reset time-out of approximately 50 μ s. Maximum
reset time-out is limited by the largest available low
leakage capacitor. The accuracy of the time-out period will
be affected by capacitor leakage (the nominal charging
current is 2 μ A) and capacitor tolerance. A low leakage
ceramic capacitor is recommended.
Selecting the Watchdog Timing Capacitor
The watchdog time-out period is adjustable and can be
optimized for software execution. The watchdog time-out
period, t WD , is adjusted by connecting a capacitor, C WT ,
between the CWT pin and ground. Given a specified
watchdog time-out period, the capacitor is determined by:
C WT = t WD ? 50 ? 10 –9
with C WT in Farads and t WD in seconds. The C WT value per
millisecond of delay can also be expressed as C WT /ms =
50 (pF/ms).
Leaving the CWT pin unconnected will generate a mini-
mum watchdog time-out of approximately 200 μ s. Maxi-
mum time-out is limited by the largest available low
leakage capacitor. The accuracy of the time-out period will
be affected by capacitor leakage (the nominal charging
current is 2 μ A) and capacitor tolerance. A low leakage
ceramic capacitor is recommended.
2901fb
13
相关PDF资料 |
PDF描述 |
|---|---|
| ESRL220M08R | CAP ALUM 22UF 8V 20% SMD |
| LTC2901-4IGN | IC MONITOR QUAD SUPP PROG 16SSOP |
| H2ABT-10102-V4-ND | JUMPER-H1502TR/A2015V/H1500TR 2" |
| VI-21H-EW-F2 | CONVERTER MOD DC/DC 52V 100W |
| H2ABT-10102-S4-ND | JUMPER-H1502TR/A2015S/H1500TR 2" |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2902-1CGN | 功能描述:IC MON SUPP QD W/RST&SEL 16-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC2902-1CGN#PBF | 功能描述:IC MONITOR SUPPLY QUAD 16-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 其它有关文件:STM6905 View All Specifications 标准包装:1 系列:- 类型:多压监控器 监视电压数目:5 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 140 ms 电压 - 阀值:2.188V，2.955V，可调，可调，可调 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-TSSOP 包装:Digi-Reel® 产品目录页面:1197 (CN2011-ZH PDF) 其它名称:497-8728-6 |
| LTC2902-1CGN#PBF | 制造商:Linear Technology 功能描述:SUPPLY MONITOR, QUAD, ADJ, 43UA, SSOP-16 |
| LTC2902-1CGN#TR | 功能描述:IC MONITOR SUPPLY QUAD 16-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC2902-1CGN#TRPBF | 功能描述:IC MON SUPP QD W/RST&SEL 16-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
发布紧急采购，3分钟左右您将得到回复。