- 您现在的位置：买卖IC网 > PDF目录44989 > LTC2935IDC-3#TRMPBF (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 PDF资料下载
参数资料
| 型号： | LTC2935IDC-3#TRMPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封装： | 2 X 2 MM, LEAD FREE, PLASTIC, DFN-8 |
| 文件页数： | 10/12页 |
| 文件大小： | 134K |
| 代理商： | LTC2935IDC-3#TRMPBF |
LTC2935
7
2935fa
APPLICATIONS INFORMATION
VOLTAGE MONITORING
Unmanaged power can cause various system problems.
At power-up, voltage uctuation around critical thresholds
can cause improper system or processor initialization.
The LTC2935 provides power management capabilities
for the system power-up phase. The supervisory device
issues a system reset after the monitored voltage has
stabilized. Built-in hysteresis and ltering ensures that
uctuations due to load transients or supply noise do
not cause chattering of the status outputs. Comparator
undervoltage glitch immunity is shown in the Typical
Performance Characteristics section. The curve dem-
onstrates the transient amplitude and width required to
switch the comparators.
Because many batteries exhibit large series resistance,
load currents can cause signicant voltage drops. The
low DC current draw of the LTC2935 (at any input volt-
age) does not add to the loading problem. When voltage
is initially applied to VCC, RST and PFO pull low once there
is enough voltage to turn on the pull-down devices (1V
maximum).
If the monitored supply voltage falls to the power-fail
threshold, the built-in power-fail comparator pulls PFO
low. At this point, there remains a voltage margin before
the RST output pulls low. PFO remains low until VCC rises
above the power-fail threshold plus 2.5% hysteresis. PFO
is typically used in signal preparation for controlled shut-
down. For example, the PFO output may be connected to
a processor nonmaskable interrupt. Upon interrupt, the
processor may begin shutdown procedures. Shutdown
events may include supply sequencing and/or storage/
erasure of system state in nonvolatile memory.
If the monitored voltage drops below the reset threshold,
RSTpullslowuntilVCCrisesabovetheresetthresholdplus
5% hysteresis. This may occur through battery charging
or replacement. An internal reset timer delays the return
of the RST output to a high state to provide settling and
initialization time. The RST output is typically connected
to a processor reset input.
Few, if any external components are necessary for reliable
operation. However, a decoupling capacitor between VCC
and ground is recommended (0.01μF minimum).
Threshold Conguration
The LTC2935 monitors and compares the VCC voltage
against two internal thresholds during operation. The
higher threshold (power-fail) is the level used for early
warning of a low voltage condition, reported on the PFO
output. The lower threshold (reset) is the level at which the
RST output pulls low. Use system requirements to choose
the appropriate reset threshold from Table 1.
Table 1. Falling Threshold Selection
LTC2935-1/LTC2935-2
LTC2935-3/LTC2935-4
RESET
THRESHOLD
(V)
POWER-FAIL
THRESHOLD
(V)
RESET
THRESHOLD
(V)
POWER-FAIL
THRESHOLD
(V)
S2
S1
S0
3.30
3.45
2.44
2.56
Low Low Low
3.15
3.30
2.32
2.44
Low Low High
3.00
3.15
2.20
2.32
Low High High
2.85
3.00
2.08
2.20
Low High Low
2.70
2.85
1.96
2.08
High High Low
2.55
2.70
1.84
1.96
High Low Low
2.40
2.55
1.72
1.84
High Low High
2.25
2.40
1.60
1.72
High High High
In the LTC2935-1/LTC2935-2 the power-fail threshold
is always 150mV higher than the congured reset
threshold. In the LTC2935-3/LTC2935-4 the power-fail
threshold is always 120mV higher than the congured
reset threshold. Set the threshold selection inputs (S2,
S1, S0) accordingly.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC2942CDCB-1#TRMPBF | POWER SUPPLY SUPPORT CKT, PDSO6 |
| LTC2942CDCB-1#TRPBF | POWER SUPPLY SUPPORT CKT, PDSO6 |
| LTC2942IDCB#TRPBF | POWER SUPPLY SUPPORT CKT, PDSO6 |
| LTC2942CDCB#TRPBF | POWER SUPPLY SUPPORT CKT, PDSO6 |
| LTC2990CMS#PBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2935IDC-4#PBF | 制造商:Linear Technology 功能描述:IC VOLTAGE MONITOR 0.5A 5.5V DFN-8 制造商:Linear Technology 功能描述:IC, VOLTAGE MONITOR, 0.5 uA, 5.5V, DFN-8; Threshold Voltage:2.44V; No. of Supervisors / Monitors:8; Supply Voltage Min:0V; Supply Voltage Max:5.5V; Reset Type:Active-Low; Digital IC Case Style:DFN; No. of Pins:8; Supply Current:500nA;RoHS Compliant: Yes |
| LTC2935IDC-4#TRMPBF | 功能描述:IC SUPERVISOR ULTRA LP 8-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 其它有关文件:STM6717 View All Specifications 标准包装:1 系列:- 类型:多压监控器 监视电压数目:2 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 600 ms 电压 - 阀值:1.11V，3.075V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:Digi-Reel® 产品目录页面:1194 (CN2011-ZH PDF) 其它名称:497-7019-6 |
| LTC2935IDC-4#TRPBF | 功能描述:IC SUPERVISOR ULTRA LP 8-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:400 系列:- 类型:备用电池电路 监视电压数目:1 输出:开路漏极，推挽式 复位:高有效/低有效 复位超时:最小为 35 ms 电压 - 阀值:4.65V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:带卷 (TR) 其它名称:ADM691ARZ-REEL7TR |
| LTC2935ITS8-1#PBF | 制造商:Linear Technology 功能描述:Volt Supervisor Monitor 5.5V 8-Pin TSOT-23 |
| LTC2935ITS8-1#TRMPBF | 功能描述:IC SUPERVISOR ULTRA LP TSOT23-8 RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:400 系列:- 类型:备用电池电路 监视电压数目:1 输出:开路漏极，推挽式 复位:高有效/低有效 复位超时:最小为 35 ms 电压 - 阀值:4.65V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:带卷 (TR) 其它名称:ADM691ARZ-REEL7TR |
发布紧急采购，3分钟左右您将得到回复。