- 您现在的位置：买卖IC网 > PDF目录44989 > LTC2942CDCB-1#TRPBF (LINEAR TECHNOLOGY CORP) POWER SUPPLY SUPPORT CKT, PDSO6 PDF资料下载
参数资料
| 型号： | LTC2942CDCB-1#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, PDSO6 |
| 封装： | 2 X 3 MM, LEAD FREE, PLASTIC, MO-229TBD, DFN-6 |
| 文件页数： | 3/16页 |
| 文件大小： | 230K |
| 代理商： | LTC2942CDCB-1#TRPBF |
LTC2942-1
29421f
applicaTions inFormaTion
Example: a register value of I[7:0] = B0h and J[7:0] = 1Ch
corresponds to a voltage on SENSE– of:
V
B C
FFFF
V
SENSE
h
DEC
–
.
=
≈
6
01
6
45084
65535
4 1276
Voltageismeasuredattheinternalbondpadsconnectedto
SENSE–, hence, the current flowing through the combined
pin and bond wire resistance causes the measured voltage
to deviate slightly from the actual battery voltage at the
SENSE– package pin. For the full-scale current of ±1A at
room temperature, this error is typically ±9mV, which is
negligible in most applications. To increase the precision
of the voltage measurement, the error can be reduced by
differentiating the coulomb counter data, multiplying the
resultant current value by 9 m, and adding or subtract-
ing the result from the voltage measurement. Note that
the sign of the error changes depending on the direction
of the current flow.
The actual temperature can be obtained from the two byte
register C[7:0]D[7:0] by:
T
K
RESULT
FFFF
K
RESULT
h
DEC
=
600
65535
Example: a register value of C[7:0] = 80h D[7:0] = 00h
corresponds to 300K or 27°C.
Temperature is measured on the surface of the chip (TDIE),
which may be different from ambient temperature TAMB,
especially with high sense resistor currents. To minimize
errorsinthetemperaturemeasurement,theDFNpackage’s
exposed pad may be thermally coupled to the body whose
temperatureistobemeasured.WiththerecommendedPCB
layout (Figure 11), TDIE typically increases over TAMB by
1K for 0.25A, 3K for 0.5A and 12K for 1A. Different results
may be obtained depending on layout, mounting details,
and air flow. Software in the host system can reduce this
error if the rise over TAMB is known by differentiating the
coulomb counter data to obtain current and using this
value to correct the temperature reading.
Threshold Registers (E, F, G, H, K, L, O, P)
For each of the measured quantities (battery charge, volt-
age and temperature) the LTC2942-1 features a high and a
low threshold registers. At power-up, the high thresholds
are set to FFFFh while the low thresholds are set to 0000h.
All thresholds can be programmed to a desired value via
I2C. As soon as a measured quantity exceeds the high
threshold or falls below the low threshold, the LTC2942-1
sets the corresponding flag in the status register and
pulls the AL/CC pin low if alert mode is enabled via bits
B[2:1]. Note that the voltage and temperature threshold
registers are single byte registers and only the 8 MSBs of
the corresponding quantity are checked. To set a low level
threshold for the battery voltage of 3V, register L should
be programmed to 80h; a high temperature limit of 60°C
is programmed by setting register O to 8Eh.
I2C Protocol
The LTC2942-1 uses an I2C/SMBus compatible 2-wire
open-drain interface supporting multiple devices and
masters on a single bus. The connected devices can only
pull the bus wires low and they never drive the bus high.
The bus wires must be externally connected to a positive
supply voltage via a current source or pull-up resistor.
When the bus is idle, both SDA and SCL are high. Data on
the I2C bus can be transferred at rates of up to 100kbit/s
in standard mode and up to 400kbit/s in fast mode.
Each device on the I2C/SMbus is recognized by a unique
address stored in that device and can operate as either a
transmitter or receiver, depending on the function of the
device. In addition to transmitters and receivers, devices
can also be classified as masters or slaves when perform-
ing data transfers. A master is the device which initiates a
data transfer on the bus and generates the clock signals
to permit that transfer. At the same time any device ad-
dressed is considered a slave. The LTC2942-1 always
acts as a slave.
Figure 3 shows an overview of the data transmission for
fast and standard mode on the I2C bus.
Start and Stop Conditions
When the bus is idle, both SCL and SDA must be high. A
bus master signals the beginning of a transmission with
a START condition by transitioning SDA from high to low
while SCL is high. When the master has finished com-
municating with the slave, it issues a STOP condition by
相关PDF资料 |
PDF描述 |
|---|---|
| LTC2942IDCB#TRPBF | POWER SUPPLY SUPPORT CKT, PDSO6 |
| LTC2942CDCB#TRPBF | POWER SUPPLY SUPPORT CKT, PDSO6 |
| LTC2990CMS#PBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LTC2990CMS#TR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LTC2990IMS#PBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2942IDCB#PBF | 制造商:Linear Technology 功能描述:BATTERY GAS GAUGE LI-ION 5.5V DFN-6 制造商:Linear Technology 功能描述:BATTERY GAS GAUGE, LI-ION, 5.5V, DFN-6 制造商:Linear Technology 功能描述:BATTERY GAS GAUGE, LI-ION, 5.5V, DFN-6, Battery Management Function:Fuel Gauge, Status Monitor, Battery Type:Li-Ion, Supply Voltage Min:2.7V, Supply Voltage Max:5.5V, Battery IC Case Style:DFN, No. of Pins:6, MSL:MSL 1 - Unlimited , RoHS Compliant: Yes 制造商:Linear Technology 功能描述:MS-System Monitor/Other, Cut Tape Battery Gas Gauge with Temperature & Voltage M |
| LTC2942IDCB#TRMPBF | 功能描述:IC FUEL/GAS GAUGE LI-ION 6DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC2942IDCB#TRPBF | 功能描述:IC FUEL/GAS GAUGE LI-ION 6DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC2942IDCB-1#PBF | 制造商:Linear Technology 功能描述:BATTERY FUEL GAUGE LI-ION 5.5V DFN-6 制造商:Linear Technology 功能描述:IC, BATTERY FUEL GAUGE, LI-ION, 5.5V, DFN-6, Battery Management Function:Fuel Gauge, Charge Controller, Battery Type:Li-Ion, Supply Voltage Min:2.7V, Supply Voltage Max:5.5V, Battery IC Case Style:DFN, No. of Pins:6 , RoHS Compliant: Yes |
| LTC2942IDCB-1#PBF | 制造商:Linear Technology 功能描述:IC BATTERY FUEL GAUGE LI-ION 5.5V DFN-6 |
发布紧急采购，3分钟左右您将得到回复。