- 您现在的位置：买卖IC网 > PDF目录16038 > LTC2942CDCB#TRPBF (Linear Technology)IC FUEL/GAS GAUGE LI-ION 6DFN PDF资料下载
参数资料
| 型号： | LTC2942CDCB#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/18页 |
| 文件大小： | 0K |
| 描述： | IC FUEL/GAS GAUGE LI-ION 6DFN |
| 标准包装： | 2,500 |
| 功能： | 燃料，电量检测计/监控器 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-WFDFN 裸露焊盘 |
| 供应商设备封装： | 6-DFN-EP（2x3） |
| 包装： | 带卷 (TR) |
| 配用： | DC1496B-B-ND - BOARD EVAL LTC2942 |
LTC2942
APPLICATIONS INFORMATION
q LSB = 0.085mAh ?
50m ? M
Q BAT R SENSE
M ≥ 128 ? ?
? 0.085mAh 50m ?
2
ChoosingCoulombCounterPrescalerMB[5:3]
If the battery capacity (Q BAT ) is very small compared to
the maximum current (I MAX ) (Q BAT < I MAX ? 0.1 Hours)
the prescaler value M should be changed from its default
value (128).
In these applications with a small battery but a high
maximum current, q LSB can get quite large with respect
to the battery capacity. For example, if the battery capacity
is 100mAh and the maximum current is 1A, the standard
equation leads to choosing a sense resistor value of
50mΩ, resulting in:
q LSB = 0.085mAh = 306mC
The battery capacity then corresponds to only 1176 q LSB s
and less than 2% of the accumulated charge register is
utilized.
To preserve digital resolution in this case, the LTC2942
includes a programmable prescaler. Lowering the pres-
caler factor M allows reducing q LSB to better match the
accumulated charge register to the capacity of the battery.
The prescaling factor M can be chosen between 1 and its
default value 128. The charge LSB then becomes:
?
R SENSE 128
To use as much of the range of the accumulated charge
register as possible the prescaler factor M should be
chosen for a given battery capacity Q BAT and a sense
resistor R SENSE as:
16
M can be set to 1, 2, 4, 8, … 128 by programming B[5:3] of
the control register as M = 2 (4 ? B[5] + 2 ? B[4] + B[3]) . The default
value after power up is M = 128 = 2 7 (B[5:3] = 111).
In the above example of a 100mAh battery and an R SENSE
of 50mΩ, the prescaler should be programmed to M = 4.
The q LSB then becomes 2.656μAh and the battery capacity
corresponds to roughly 37650 q LSB s.
Note that the internal digital resolution of the coulomb
counter is higher than indicated by q LSB . The digitized
charge q INTERNAL is M ? 8 times smaller than q LSB . q INTERNAL
is typically 299μAs for a 50mΩ sense resistor.
ADC Mode B[7:6]
The LTC2942 features an ADC which measures either
voltage on SENSE – (battery voltage) or temperature via
an internal temperature sensor. The reference voltage and
clock for the ADC are generated internally.
The ADC has four different modes of operation, as shown
in Table 3. These modes are controlled by bits B[7:6] of
the control register. At power-up, bits B[7:6] are set to
[00] and the ADC is in sleep mode.
A single voltage conversion is initiated by setting the bits
B[7:6] to [10]. A single temperature conversion is started
by setting bits B[7:6] to [01]. After a single voltage or
temperature conversion, the ADC resets B[7:6] to [00]
and goes to sleep.
The LTC2942 also offers an automatic scan mode where
the ADC converts voltage, then temperature, then sleeps
for approximately two seconds before repeating the voltage
and temperature conversions. The LTC2942 is set to this
automatic mode by setting B[7:6] to [11] and stays in this
mode until B[7:6] are reprogrammed by the host.
Programming B[7:6] to [00] puts the ADC to sleep. If
control bits B[7:6] change within a conversion, the ADC
will complete the current conversion before entering the
newly selected mode.
A conversion of either voltage or temperature requires 10ms
conversion time (typical). At the end of each conversion,
the corresponding registers are updated. If the converted
quantity exceeds the values programmed in the threshold
registers, a flag is set in the status register and the AL /CC
pin is pulled low (if alert mode is enabled).
During a voltage conversion, the SENSE – pin is connected
through a small resistor to a sampling circuit with an
equivalent resistance of 2MΩ, leading to a mean input
current of I = V SENSE– /2MΩ.
2942fa
11
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6753KA46+T | IC MPU/RESET CIRC SOT23-8 |
| 415-0029-018 | CABLE SMA/SMA 18" RG-316 |
| MAX6751KA29+T | IC MPU/RESET CIRC SOT23-8 |
| LTC4054ES5-4.2#TRM | IC CHARGR BATTERY L-ION TSOT23-5 |
| LTC4054XES5-4.2#TRMPBF | IC CHARGR BATTERY L-ION TSOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2942IDCB#PBF | 制造商:Linear Technology 功能描述:BATTERY GAS GAUGE LI-ION 5.5V DFN-6 制造商:Linear Technology 功能描述:BATTERY GAS GAUGE, LI-ION, 5.5V, DFN-6 制造商:Linear Technology 功能描述:BATTERY GAS GAUGE, LI-ION, 5.5V, DFN-6, Battery Management Function:Fuel Gauge, Status Monitor, Battery Type:Li-Ion, Supply Voltage Min:2.7V, Supply Voltage Max:5.5V, Battery IC Case Style:DFN, No. of Pins:6, MSL:MSL 1 - Unlimited , RoHS Compliant: Yes 制造商:Linear Technology 功能描述:MS-System Monitor/Other, Cut Tape Battery Gas Gauge with Temperature & Voltage M |
| LTC2942IDCB#TRMPBF | 功能描述:IC FUEL/GAS GAUGE LI-ION 6DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC2942IDCB#TRPBF | 功能描述:IC FUEL/GAS GAUGE LI-ION 6DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC2942IDCB-1#PBF | 制造商:Linear Technology 功能描述:BATTERY FUEL GAUGE LI-ION 5.5V DFN-6 制造商:Linear Technology 功能描述:IC, BATTERY FUEL GAUGE, LI-ION, 5.5V, DFN-6, Battery Management Function:Fuel Gauge, Charge Controller, Battery Type:Li-Ion, Supply Voltage Min:2.7V, Supply Voltage Max:5.5V, Battery IC Case Style:DFN, No. of Pins:6 , RoHS Compliant: Yes |
| LTC2942IDCB-1#PBF | 制造商:Linear Technology 功能描述:IC BATTERY FUEL GAUGE LI-ION 5.5V DFN-6 |
发布紧急采购，3分钟左右您将得到回复。