- 您现在的位置：买卖IC网 > PDF目录69007 > LTC2991IMS#TRPBF (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 PDF资料下载
参数资料
| 型号： | LTC2991IMS#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| 封装： | LEAD FREE, PLASTIC, MSOP-16 |
| 文件页数： | 6/32页 |
| 文件大小： | 230K |
| 代理商： | LTC2991IMS#TRPBF |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC2991
14
2991f
APPLICATIONS INFORMATION
In the case of current measurements, the external sense
resistor is typically small, and determined by the full-scale
input voltage of the LTC2991. The full-scale differential
voltage is 0.300V. The external sense resistance, is then a
function of the maximum measurable current, or REXT_MAX
= 0.300V/IMAX. For example, if you wanted to measure a
current range of ±5A, the external shunt resistance would
equal 0.300V/5A = 60mΩ.
There exists a way to improve the sense resistor’s precision
using the LTC2991. The LTC2991 measures both differential
voltage and remote temperature. It is therefore, possible
to compensate for the absolute resistance tolerance of the
sense resistor and the temperature coefficient of the sense
resistor in software. The resistance would be measured
by running a calibrated test current through the discrete
resistor. The LTC2991 would measure both the differential
voltage across this resistor and the resistor temperature.
From this measurement, RO and TO in the following equa-
tion would be known. Using the two equations, the host
microprocessor could compensate for both the absolute
tolerance and the TCR.
RT = RO [1 + α(T – TO)],where
α = 3930ppm/°C for copper trace
α = ±2 to ~200ppm/°C for discrete R
(7)
I = (V1 – V2)/RT
(8)
Device Configuration
The LTC2991 is configured by writing the channel control
registers through the serial interface. Refer to Tables 5, 6
and 7 for control register bit definition. The device is ca-
pable of many application configurations including voltage,
temperature and current measurements. It is possible to
configure the device for single or repeated acquisitions. For
repeated acquisitions, only the initial trigger is required,
and new data is written over the old data. Acquisitions
are frozen during serial read data transfers, to prevent the
upper and lower data bytes for a particular measurement
from becoming out of sync. Internally, both the upper and
lower bytes are written at the same instant. Since serial data
transfer timeout is not implemented, failure to terminate a
read operation will yield an indefinitely frozen wait state.
The device can also make single measurements, or with
one trigger, all of the measurements for the configuration.
When the device is configured for multiple measurements,
the order of measurements is fixed. As each new data
result is ready, the MSB of the corresponding data reg-
ister is set, and the corresponding status register bit is
set. These bits are cleared when the corresponding data
register is addressed. The configuration register value at
power-up yields the measurement of the internal tempera-
ture sensor and V1 through V8 as single-ended voltages,
if triggered. The eight input pins V1 through V8 will be in
a high impedance state, until configured otherwise, and
a measurement triggered.
Data Format
The data registers are broken into 8-bit upper and lower
bytes. Voltage and temperature conversions are 13-bits.
The upper bits in the MSB registers provide status on the
resulting conversions. These status bits are different for
temperature and voltage conversions.
Temperature
Temperature conversions are reported as Celsius or Kelvin
results described in Tables 11 and 12, each with 0.0625
degree weighted LSBs. The format is controlled by the
control registers, xxx. The temperature MSB result register
most significant bit (Bit 7) is the DATA_VALID bit, which
indicates whether the current register contents have been
accessed since the result was written to the register. This
bit will be set when new data is written to the register,
and cleared when accessed. The LTC2991 internal bias
circuitry maintains this voltage above this level during
normal operating conditions. Bit 4 through bit 0 of the
MSB register are the conversion result bits D[12:8], in
two’s compliment format. Note in Kelvin results, the
result will always be positive. The LSB register contains
temperature result bits D[7:0]. To convert the register
contents to temperature, use the following equation: T =
D[12:0]/16. See Table 16 for conversion value examples.
Remote diode voltage is digitized at ~50μA of bias current.
The ADC LSB value during these conversions is typically
38.15μV. Voltages are only available for the remote di-
odes, not the internal sensor. This code repeats at a diode
voltage of approximately 0.625V (see Tables 13 and 14).
The absolute temperature of the diode can be used to
detect whether the diode is operating (≤0.62501V or
≥ 0.62505V). This mode is useful for testing small relative
相关PDF资料 |
PDF描述 |
|---|---|
| LTC2991IMS#PBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| LTC3406AES5#TRM | 1.3 A SWITCHING REGULATOR, 1800 kHz SWITCHING FREQ-MAX, PDSO5 |
| LTC3406AES5#TR | 1.3 A SWITCHING REGULATOR, 1800 kHz SWITCHING FREQ-MAX, PDSO5 |
| LTC3406AIS5#PBF | 1.3 A SWITCHING REGULATOR, 1800 kHz SWITCHING FREQ-MAX, PDSO5 |
| LTC3406AES5#PBF | 1.3 A SWITCHING REGULATOR, 1800 kHz SWITCHING FREQ-MAX, PDSO5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2995CUD#PBF | 功能描述:IC TEMP SENSOR VOLT MNTR 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:2,500 系列:SilentSense™ 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-55°C ~ 125°C，外部传感器 精确度:±2°C 本地（最大），±3°C 远程（最大） 拓扑:ADC（三角积分型），比较器，寄存器库 输出类型:I²C?/SMBus? 输出警报:是 输出风扇:是 电源电压:2.7 V ~ 5.5 V 工作温度:-55°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR) 其它名称:MIC284-2BMMTRMIC284-2BMMTR-ND |
| LTC2995CUD#TRPBF | 功能描述:IC TEMP SENSOR VOLT MNTR 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:2,500 系列:SilentSense™ 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-55°C ~ 125°C，外部传感器 精确度:±2°C 本地（最大），±3°C 远程（最大） 拓扑:ADC（三角积分型），比较器，寄存器库 输出类型:I²C?/SMBus? 输出警报:是 输出风扇:是 电源电压:2.7 V ~ 5.5 V 工作温度:-55°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR) 其它名称:MIC284-2BMMTRMIC284-2BMMTR-ND |
| LTC2995HUD#PBF | 功能描述:IC TEMP SENSOR VOLT MNTR 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:2,500 系列:SilentSense™ 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-55°C ~ 125°C，外部传感器 精确度:±2°C 本地（最大），±3°C 远程（最大） 拓扑:ADC（三角积分型），比较器，寄存器库 输出类型:I²C?/SMBus? 输出警报:是 输出风扇:是 电源电压:2.7 V ~ 5.5 V 工作温度:-55°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR) 其它名称:MIC284-2BMMTRMIC284-2BMMTR-ND |
| LTC2995HUD#TRPBF | 功能描述:IC TEMP SENSOR VOLT MNTR 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:2,500 系列:SilentSense™ 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-55°C ~ 125°C，外部传感器 精确度:±2°C 本地（最大），±3°C 远程（最大） 拓扑:ADC（三角积分型），比较器，寄存器库 输出类型:I²C?/SMBus? 输出警报:是 输出风扇:是 电源电压:2.7 V ~ 5.5 V 工作温度:-55°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR) 其它名称:MIC284-2BMMTRMIC284-2BMMTR-ND |
| LTC2995IUD#PBF | 功能描述:IC TEMP SENSOR VOLT MNTR 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:3,000 系列:- 功能:温度开关 传感器类型:内部 感应温度:85°C 分界点 精确度:±6°C（最小值） 拓扑:ADC（三角积分型），比较器，寄存器库 输出类型:开路漏极 输出警报:是 输出风扇:是 电源电压:2.7 V ~ 5.5 V 工作温度:-55°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:ADT6501SRJZP085RL7-ND |
发布紧急采购，3分钟左右您将得到回复。