参数资料
| 型号： | LTC3026EDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/18页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ 1.5A 10-DFN |
| 产品培训模块： | More Information on LDOs |
| 标准包装： | 2,500 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 0.4 V ~ 2.6 V |
| 输入电压： | 1.14 V ~ 5.5 V |
| 电压 - 压降（标准）： | 0.1V @ 1.5A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 1.5A（最小） |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-DFN（3x3） |
| 包装： | 带卷 (TR) |
LTC3026
PIN FUNCTIONS
IN (Pins 1, 2): Input Supply Voltage. Output load current
is supplied directly from IN. The IN pin should be locally
bypassed to ground if the LTC3026 is more than a few
inches away from another source of bulk capacitance.
In general, the output impedance of a battery rises with
frequency, so it is usually advisable to include an input
bypass capacitor when supplying IN from a battery. A
capacitor in the range of 0.1μF to 4.7μF is usually sufficient.
GND (Pin 3, Exposed Pad Pin 11): Ground and Heat Sink.
Connect the exposed pad to the PCB ground plane or large
pad for optimum thermal performance.
SW (Pin 4): Boost Switching Pin. This is the boost converter
switching pin. A 4.7μH to 40μH inductor able to handle a
peak current of 150mA is connected from this pin to V IN .
The boost converter can be disabled by floating this pin.
This allows the use of an external boosted supply from
a second LTC3026 or other source. See Operating with
Boost Converter Disabled section for more information.
BST (Pin 5): Boost Output Voltage Pin. With boost con-
verter enabled bypass the BST pin with a ≥4.7μF low ESR
ceramic capacitor to GND (C BST ). BST does not load V IN
when in shutdown, but is diode connected to IN through
the external inductor, thus, will not go to ground with V IN
present. Users should not present any loads to the BST
pin (with boost enabled) until PG signals that regulation
has been achieved. When providing an external BST volt-
age (i.e. boost converter disabled) a 1μF low ESR ceramic
capacitor can be used.
SHDN (Pin 6): Shutdown Input Pin, Active Low. This pin
is used to put the LTC3026 into shutdown. The SHDN pin
current is typically less than 10nA. The SHDN pin cannot
be left floating and must be tied to a valid logic level (such
as IN) if not used.
PG (Pin 7): Power Good Pin. When PG is high impedance
OUT is in regulation, and low impedance when OUT is in
shutdown or out of regulation.
ADJ (Pin 8): Output Adjust Pin. This is the input to the error
amplifier. It has a typical bias current of 0.1nA flowing into
the pin. The ADJ pin reference voltage is 0.4V referenced
to ground. The output voltage range is 0.4V to 2.6V and is
typically set by connecting ADJ to a resistor divider from
OUT to GND. See Figure 2.
OUT (Pins 9, 10): Regulated Output Voltage. The OUT pins
supply power to the load. A minimum output capacitance
of 5μF is required to ensure stability. Larger output capaci-
tors may be required for applications with large transient
loads to limit peak voltage transients. See the Applica-
tions Information section for more information on output
capacitance.
3026ff
7
相关PDF资料 |
PDF描述 |
|---|---|
| RSC30DRTI-S93 | CONN EDGECARD 60POS DIP .100 SLD |
| LT3012EFE#TRPBF | IC REG LDO ADJ .25A 16-TSSOP |
| RMC30DRTI-S93 | CONN EDGECARD 60POS DIP .100 SLD |
| MIC29204YM | IC REG LDO 5V/ADJ .4A 8SOIC |
| RSC31DRTH-S93 | CONN EDGECARD 62POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3026EMSE | 制造商:Linear Technology 功能描述:LDO Regulator Pos 0.4V to 2.6V 1.5A 10-Pin MSOP EP |
| LTC3026EMSE#PBF | 功能描述:IC REG LDO ADJ 1.5A 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:8V 输入电压:10.5 V ~ 23 V 电压 - 压降（标准）:1.7V @ 40mA 稳压器数量:1 电流 - 输出:100mA（最小值） 电流 - 限制（最小）:- 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:剪切带 (CT) 产品目录页面:1075 (CN2011-ZH PDF) 其它名称:296-24390-1 |
| LTC3026EMSE#PBF | 制造商:Linear Technology 功能描述:Linear Voltage Regulator IC |
| LTC3026EMSE#TR | 制造商:Linear Technology 功能描述:LDO Regulator Pos 0.4V to 2.6V 1.5A 10-Pin MSOP EP T/R |
| LTC3026EMSE#TRPBF | 功能描述:IC REG LDO ADJ 1.5A 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:800 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:最高 16V 电压 - 压降（标准）:0.7V @ 4A 稳压器数量:1 电流 - 输出:4A 电流 - 限制（最小）:4.2A 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-6，D²Pak（5 引线+接片），TO-263BA 供应商设备封装:TO-263-5 包装:带卷 (TR) 其它名称:AP1184K525L-13AP1184K525LDITR |
发布紧急采购，3分钟左右您将得到回复。