- 您现在的位置：买卖IC网 > PDF目录20847 > LTC3202EMS (Linear Technology)IC LED DRVR WHITE BCKLGT 10-MSOP PDF资料下载
参数资料
| 型号： | LTC3202EMS |
| 厂商： | Linear Technology |
| 文件页数： | 6/12页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR WHITE BCKLGT 10-MSOP |
| 标准包装： | 50 |
| 拓扑： | PWM，切换式电容器（充电泵） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 1.5MHz |
| 电源电压： | 2.7 V ~ 4.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 85°C |
LTC3202
OPERATIO
(Refer to Simplified Block Diagram)
The LTC3202 uses a fractional conversion switched ca-
pacitor charge pump to boost V OUT to as much as 1.5 times
the input voltage. A two-phase nonoverlapping clock acti-
vates the charge pump switches. On the first phase of the
clock the flying capacitors are charged in series from V IN .
On the second phase of the clock they are connected in
parallel and stacked on top of V IN . This sequence of
charging and discharging the flying capacitors continues
at a free running frequency of 1.5MHz (typ).
Regulation is achieved by sensing the voltage at the FB pin
and modulating the charge pump strength based on the
error signal. The control pins, D0 and D1, program the set
point of the internal digital-to-analog converter. The regu-
lation loop will increase V OUT until FB comes to balance at
the set-point voltage. Table 1 shows the regulation voltage
as a function of D0 and D1.
Table 1. Feedback Control Voltage Settings
conditions it will automatically limit its output current to
approximately 250mA. At higher temperatures, or if the
input voltage is high enough to cause excessive self
heating on-chip, thermal shutdown circuitry will
shut down the charge pump when the junction tempera-
ture exceeds approximately 160 ° C. It will reenable the
charge pump once the junction temperature drops back to
approximately 155 ° C. The LTC3202 will cycle in and out of
thermal shutdown indefinitely without latchup or damage
until the short-circuit on V OUT is removed.
Soft-Start
To prevent excessive current flow at V IN during start-up,
the LTC3202 has built-in soft-start circuitry. Soft-start is
achieved by increasing the amount of current available to
the output charge storage capacitor linearly over a period
of approximately 500 μ s.
D1
0
0
1
1
D0
0
1
0
1
Feedback Set Point Voltage
Shutdown
0.2V
0.4V
0.6V
The soft-start feature activates any time an input, D0 or D1,
changes state. This will prevent large inrush current
during initial start-up as well as when the feedback setting
is changed from one value to the next. Note that the set
point voltage will drop to zero during the soft-start period.
Under heavy load conditions there may be observable
In shutdown mode all circuitry is turned off and the
LTC3202 draws only leakage current from the V IN supply.
Furthermore, V OUT is disconnected from V IN . The D0 and
D1 pins are CMOS inputs with a threshold voltage of
approximately 0.8V. The LTC3202 is in shutdown when a
logic low is applied to both D0 and D1. Since the D0 and D1
pins are high impedance CMOS inputs they should never
be allowed to float. To ensure that their states are defined
they must always be driven with valid logic levels.
droop at V OUT until the soft-start circuit catches up.
Programming the LTC3202 for Voltage or Current
The LTC3202 can be configured to control either a voltage
or a current. In white LED applications the LED current is
programmed by the ratio of the feedback set point voltage
and a sense resistor as shown in Figure 1. The current of
the remaining LEDs is controlled by virtue of their similar-
ity to the reference LED and the ballast voltage across the
Shutdown Current
Output voltage detection circuitry will draw a current of
5 μ A when the LTC3202 is in shutdown. This current will be
eliminated when the output voltage (V OUT ) is at 0V. To
ensure that V OUT is at 0V in shutdown a bleed resistor can
be used from V OUT to GND. 10k to 100k is acceptable.
sense resistor.
V OUT
LTC3202
FB
GND
5, 11
3
2
I LED =
1 μ F
V FB
R X
R X
???
R X
Short-Circuit/Thermal Protection
The LTC3202 has built-in short-circuit current limiting as
well as over temperature protection. During short-circuit
Figure 1. Current Control Mode
3202 F01
3202fa
6
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3201EMS#PBF | IC LED DRVR WHITE BCKLGT 10-MSOP |
| VLCF4020T-6R8N1R0 | INDUCTOR POWER 6.8UH 1.0A SMD |
| P51-3000-S-M-I12-4.5V-000-000 | SENSOR 3000PSI M10-1.0 6G 4.5V |
| REC5-2409SRW/H2/C/M/SMD-R | CONV DC/DC 5W 18-36VIN 09VOUT |
| REC5-483.3DRW/H2/A/M/SMD/CTRL | CONV DC/DC 5W 36-72VIN +/-3.3V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3202EMS#PBF | 功能描述:IC LED DRVR WHITE BCKLGT 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LTC3202EMS#TR | 功能描述:IC LED DRVR WHITE BCKLGT 10-MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LTC3202EMS#TRPBF | 功能描述:IC LED DRVR WHITE BCKLGT 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LTC3203 | 制造商:LINER 制造商全称:Linear Technology 功能描述:500mA Output Current Low Noise Dual Mode Step-Up Charge Pumps |
| LTC3203-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:500mA Output Current Low Noise Dual Mode Step-Up Charge Pumps |
发布紧急采购，3分钟左右您将得到回复。