- 您现在的位置：买卖IC网 > PDF目录14121 > LTC3203BEDD-1#PBF (Linear Technology)IC REG BST SWITCHED CAP 5V 10DFN PDF资料下载
参数资料
| 型号： | LTC3203BEDD-1#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BST SWITCHED CAP 5V 10DFN |
| 标准包装： | 121 |
| 类型： | 升压（升压），切换电容（充电泵） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 5V |
| 输入电压： | 2.7 V ~ 5.5 V |
| PWM 型： | Burst Mode? |
| 频率 - 开关： | 900kHz，1MHz |
| 电流 - 输出： | 500mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 10-DFN（3x3） |
LTC3203/LTC3203-1
LTC3203B/LTC3203B-1
OPERATIO
The LTC3203/LTC3203-1/LTC3203B/LTC3203B-1 use
a switched capacitor charge pump to boost V IN to a
regulated output voltage. Regulation is achieved by sens-
ing the output voltage through a resistor divider and
modulating the charge pump output current based on the
error signal. A two-phase non-overlapping clock activates
the charge pump switches. The typical frequency of charg-
ing and discharging the flying capacitors is 1MHz
(2x mode) or 0.9MHz (1.5x mode). A unique architecture
maintains relatively constant input current for the lowest
possible input noise.
Mode of Operation
The LTC3203/LTC3203-1/LTC3203B/LTC3203B-1 charge
pump can operate in two modes of voltage conversion:
1.5x or 2x.
In the 1.5x mode the flying capacitors are charged in series
during the first clock phase, and stacked in parallel on top
of V IN on the second clock phase. Alternatively, in the 2x
mode the flying capacitors are charged on alternate clock
phases from V IN . While one capacitor is being charged
from V IN , the other is stacked on top of V IN and connected
to the output. The two flying capacitors operate out of
phase to minimize both input and output ripple. At light
load the LTC3203/LTC3203-1 go into Burst Mode opera-
tion to reduce quiescent current.
The conversion mode should be chosen based on consid-
erations of efficiency, available output current and V OUT
ripple. With a given V IN , the 1.5x mode gives a higher
efficiency but lower available output current. The 2x mode
gives a higher available output current but lower effi-
ciency. Moreover, the output voltage ripple in the 2x mode
is lower due to the out-of-phase operation of the two
flying capacitors.
Generally, at low V IN , the 2x mode should be selected, and
at higher V IN , the 1.5x mode should be selected. By
connecting a resistive divider from V IN to the MODE input
pin the MODE input allows the user to accurately program
the V IN threshold at which the charge pump will switch
from 1.5x mode to 2x mode when V IN starts to fall and
vice versa. Hysteresis on the MODE pin prevents the
LTC3203/LTC3203-1/LTC3203B/LTC3203B-1 from
switching continuously between the two modes.
Output Voltage Programming
The LTC3203-1/LTC3203B-1 has a V SEL input pin that
allows the user to program the regulated output voltage to
either 4.5V or 5V. 4.5V V OUT is useful for driving white
LEDs while a regulated V OUT of 5V is useful for powering
logic circuits.
The LTC3203/LTC3203B has a FB pin in place of the V SEL
pin that allows the output voltage to be programmed using
an external resistive divider.
Shutdown Mode
When SHDN is asserted low, the LTC3203/LTC3203-1/
LTC3203B/LTC3203B-1 enter shutdown mode. The charge
pump is first disabled, but the LTC3203/LTC3203-1/
LTC3203B/LTC3203B-1 continue to draw 5 μ A of supply
current. This current will drop to less than 1 μ A when V OUT
is fully discharged to 0V. Furthermore, V OUT is discon-
nected from V IN . Since the SHDN pin is a high impedance
CMOS input, it should never be allowed to float.
Burst Mode Operation
The LTC3203/LTC3203-1 provide automatic Burst Mode
operation to reduce quiescent current of the power con-
verter at light loads. Burst Mode operation is initiated if the
output load current falls below an internally programmed
threshold. Once Burst Mode operation is initiated, the part
shuts down the internal oscillator to reduce the switching
losses and goes into a low current state. This state is
referred to as the Sleep state in which the chip consumes
only about 120 μ A from the input.
32031fa
8
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JTR-CZ-F4 | CONVERTER MOD DC/DC 7.5V 25W |
| GCA49DTMS | CONN EDGECARD 98POS R/A .125 SLD |
| GCM22DTBI-S189 | CONN EDGECARD 44POS R/A .156 SLD |
| MLS212M060EA0C | CAP ALUM 2100UF 60V 20% RADIAL |
| GCA49DTBS | CONN EDGECARD 98POS R/A .125 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3203EDD | 制造商:LINER 制造商全称:Linear Technology 功能描述:500mA Output Current Low Noise Dual Mode Step-Up Charge Pumps |
| LTC3203EDD#PBF | 功能描述:IC REG BST SWITCHD CAP ADJ 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3203EDD#TRPBF | 功能描述:IC REG BST SWITCHD CAP ADJ 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3203EDD-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:500mA Output Current Low Noise Dual Mode Step-Up Charge Pumps |
| LTC3203EDD-1#PBF | 功能描述:IC REG BOOST SWITCHED CAP 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
发布紧急采购，3分钟左右您将得到回复。