参数资料
型号: LTC3210EUD#TRPBF
厂商: Linear Technology
文件页数: 7/16页
文件大小: 0K
描述: IC LED DRIVR WHITE BCKLGT 16-QFN
标准包装: 2,500
拓扑: 升压(升压),切换式电容器(充电泵)
输出数: 5
内部驱动器:
类型 - 主要: 背光
类型 - 次要: 白色 LED
频率: 800kHz
电源电压: 2.9 V ~ 4.5 V
安装类型: 表面贴装
封装/外壳: 16-WFQFN 裸露焊盘
供应商设备封装: 16-QFN-EP(3x3)
包装: 带卷 (TR)
工作温度: -40°C ~ 85°C
LTC3210
PIN FUNCTIONS
C1P, C2P, C1M, C2M (Pins 1, 16, 14, 13): Charge Pump
Flying Capacitor Pins. A 2.2μF X7R or X5R ceramic ca-
pacitor should be connected from C1P to C1M and C2P
to C2M.
CPO (Pin 2): Output of the Charge Pump Used to Power
All LEDs. This pin is enabled or disabled using the ENM
and ENC inputs. A 2.2μF X5R or X7R ceramic capacitor
should be connected to ground.
ENM, ENC (Pins 3, 10): Inputs. The ENM and ENC pins
are used to program the LED output currents. Each input
is strobed up to 7 times to decrement the internal 3-bit
DACs from full-scale to 1LSB. The counter will stop at
1 LSB if the strobing continues. The pin must be held
high after the final desired positive strobe edge. The data
is transferred after a 150μs (typ) delay. Holding the ENM
or ENC pin low will set the LED current to 0 and will reset
the counter after 150μs (typ). If both inputs are held low
for longer than 150μs (typ) the part will go into shutdown.
The charge pump mode is reset to 1x whenever ENC goes
low or when the part is in shutdown mode.
MLED1, MLED2, MLED3, MLED4 (Pins 4, 5, 6, 7):
Outputs. MLED1 to MLED4 are the MAIN current source
outputs. The LEDs are connected between CPO (anodes)
and MLED1-4 (cathodes). The current to each LED output
is set via the ENM input, and the programming resistor
connected between RM and GND. Each of the four LED
outputs can be disabled by connecting the output directly
to CPO. A 10μA current will flow through each directly
connected LED output.
RM, RC (Pins 8, 9): LED Current Programming Resistor
Pins. The RM and RC pins will servo to 1.2V. Resistors
connected between each of these pins and GND are used
to set the CLED and MLED current levels. Connecting
a resistor 12k or less will cause the LTC3210 to enter
overcurrent shutdown.
CLED (Pin 11): Output. CLED is the CAM current source
output. The LED is connected between CPO (anode) and
CLED (cathode). The current to the LED output is set via
the ENC input, and the programming resistor connected
between RC and GND.
GND (Pin 12): Ground. This pin should be connected to
a low impedance ground plane.
V BAT (Pin 15): Supply voltage. This pin should be bypassed
with a 2.2μF, or greater low ESR ceramic capacitor.
Exposed Pad (Pin 17): This pad should be connected
directly to a low impedance ground plane for optimal
thermal and electrical performance.
3210fb
 
相关PDF资料
PDF描述
LTC3212EDDB#TRPBF IC LED DRIVER RGB 12-DFN
LTC3214EDD#TRPBF IC LED DRIVR WHITE BCKLGT 10-DFN
LTC3215EDD#PBF IC LED DRIVR WHITE BCKLGT 10-DFN
LTC3217EUD#TRPBF IC LED DRVR FLASH TORCH 16QFN
LTC3218EDDB#TRPBF IC LED DRVR FLASH TORCH 10DFN
相关代理商/技术参数
参数描述
LTC3212 制造商:LINER 制造商全称:Linear Technology 功能描述:RGB LED Driver and Charge Pump
LTC3212EDDB#PBF 制造商:Linear Technology 功能描述:DP-Charge Pump/LED Driver, CUT TAPE RGB LED Driver & Charge Pump
LTC3212EDDB#TRMPBF 功能描述:IC LED DRIVER RGB 12-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极,PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND
LTC3212EDDB#TRPBF 功能描述:IC LED DRIVER RGB 12-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极,PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND
LTC3212EDDB-PBF 制造商:LINER 制造商全称:Linear Technology 功能描述:RGB LED Driver and Charge Pump