- 您现在的位置：买卖IC网 > PDF目录20886 > LTC3217EUD#PBF (Linear Technology)IC LED DRVR FLASH TORCH 16QFN PDF资料下载
参数资料
| 型号： | LTC3217EUD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/12页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR FLASH TORCH 16QFN |
| 标准包装： | 121 |
| 拓扑： | PWM，升压（升压），切换式电容器（充电泵） |
| 输出数： | 4 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 闪灯/白光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 600kHz ~ 1.15MHz |
| 电源电压： | 2.9 V ~ 4.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 供应商设备封装： | 16-QFN-EP（3x3） |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 85°C |
LTC3217
OPERATION
The LED currents are delivered by the four programmable
current sources. Three discrete current settings (Low, High,
Low + High) are available and may be selected via the EN1
and EN2 pins. The values of these currents may be selected
by choosing the appropriate programming resistors. Each
resistor is connected between the I SET1 or I SET2 pin to
ground. The resistor values required to attain the desired
current levels can be determined by Equation 1.
Charge Pump Strength and Regulation
Regulation is achieved by sensing the voltage at the CPO
pin and modulating the charge pump strength based
on the error signal. The CPO regulation voltages are set
internally, and are dependent on the charge pump modes
as shown in Table 1.
When the LTC3217 operates in either 1.5x mode or 2x mode,
R SET 1 / 2 =
488
I LEDx
(1)
the charge pump can be modeled as a Thevenin-equivalent
circuit to determine the amount of current available from
the effective input voltage and effective open-loop output
An R SETx resistor value of 2k or less (i.e., short-circuit) will
cause the LTC3217 to enter overcurrent shutdown mode.
resistance, R OL (Figure 1).
Table 1. Charge Pump Output Regulation Voltages
This mode prevents damage to the part and external LEDs
by shutting down the high power sections of the part.
Each LED output can be disabled by connecting the pin
directly to CPO. Do not leave pins open as this will cause
CHARGE PUMP MODE
1.5x
2x
REGULATED V CPO
4.5V
5.05V
dropout and subsequently mode changing.
Pulse Width Modulation Option
EN2 can be pulse width modulated to control the
LED brightness. The minimum allowable pulse width is
50μs and the maximum low time is 1ms. Pulse width
modulating the EN2 input can be performed with EN1 high
or low. If EN1 is high then there is no limitation on the
EN2 low time. When EN1 is low the part would normally
go into shutdown whenever EN2 goes low. Prevention
of shutdown in this case is achieved by an internal timer
which delays shutdown until EN2 has remained low for
at least 1ms.
Soft-Start
R OL is dependent on a number of factors including the
switching term, 1/(2f OSC ? C FLY ), internal switch resistances
and the non-overlap period of the switching circuit. However,
for a given R OL , the amount of current available will be directly
proportional to the advantage voltage of 1.5V BAT – V CPO for
1.5x mode and 2V BAT – V CPO for 2x mode. Consider the
example of driving white LEDs from a 3.1V supply. If the
LED forward voltage is 3.8V and the current sources require
100mV, the advantage voltage for 1.5x mode is 3.1V ? 1.5
– 3.8V – 0.1V or 750mV. Notice that if the input voltage is
raised to 3.2V, the advantage voltage jumps to 900mV—a
20% improvement in available strength.
From Figure 1, for 1.5x mode the available current is
given by:
Initially, when the part is in shutdown, a weak switch
connects V BAT to CPO. This allows V BAT to slowly charge
I OUT =
1.5 V BAT – V CPO
R OL
(2)
the CPO output capacitor and prevent large charging
currents to occur.
For 2x mode, the available current is given by:
The LTC3217 also employs a soft-start feature on its
charge pump to prevent excessive inrush current and
I OUT =
2 V BAT – V CPO
R OL
(3)
supply droop when switching into the step-up modes. The
current available to the CPO pin is increased linearly over
a typical period of 125μs. Soft-start occurs at the start of
both 1.5x and 2x mode changes.
Notice that the advantage voltage in this case is
3.1V ? 2 – 3.8V – 0.1V = 2.3V. R OL is higher in 2x mode
but a signi?cant overall increase in available current is
achieved.
3217fa
7
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3210EUD-1#PBF | IC LED DRIVR WHITE BCKLGT 16-QFN |
| P51-200-S-B-MD-4.5V-000-000 | SENSOR 200PSI 1/8-27NPT .5-4.5V |
| P51-1000-S-S-D-4.5V-000-000 | SENSOR 1000PSI 1/4-18NPT .5-4.5V |
| P51-1000-A-D-M12-4.5OVP-000-000 | SENSOR 1000PSI 7/16-20UNF 4.5V |
| P51-15-S-T-I36-20MA-000-000 | SENSOR 15PSIS 7/16 4-20 MA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3218 | 制造商:LINER 制造商全称:Linear Technology 功能描述:400mA Single Wire Camera LED Charge Pump |
| LTC3218EDDB#PBF | 制造商:Linear Technology 功能描述:DP-Charge Pump/LED Driver, CUT TAPE 400mA, Single Wire Camera LED Charge Pump |
| LTC3218EDDB#TRMPBF | 功能描述:IC LED DRVR FLASH TORCH 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LTC3218EDDB#TRPBF | 功能描述:IC LED DRVR FLASH TORCH 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LTC3218EDDBPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:400mA Single Wire Camera LED Charge Pump |
发布紧急采购，3分钟左右您将得到回复。