- 您现在的位置：买卖IC网 > Datasheet目录338 > LTC3217EUD#TRPBF (Linear Technology)IC LED DRVR FLASH TORCH 16QFN Datasheet资料下载
参数资料
| 型号： | LTC3217EUD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR FLASH TORCH 16QFN |
| 标准包装： | 2,500 |
| 拓扑： | PWM，升压（升压），切换式电容器（充电泵） |
| 输出数： | 4 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 闪灯/白光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 600kHz ~ 1.15MHz |
| 电源电压： | 2.9 V ~ 4.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 供应商设备封装： | 16-QFN-EP（3x3） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
LTC3217
APPLICATIONS INFORMATION
and Y5V capacitors may also have a very poor voltage
coef?cient causing them to lose 60% or more of their
capacitance when the rated voltage is applied. There-
fore, when comparing different capacitors, it is often
more appropriate to compare the amount of achievable
capacitance for a given case size rather than comparing
the speci?ed capacitance value. For example, over rated
voltage and temperature conditions, a 1μF, 10V, Y5V
ceramic capacitor in a 0603 case may not provide any
more capacitance than a 0.22μF, 10V, X7R available in
the same case. The capacitor manufacturer’s data sheet
should be consulted to determine what value of ca-
pacitor is needed to ensure minimum capacitances at all
temperatures and voltages.
Table 2 shows a list of ceramic capacitor manufacturers
and how to contact them:
Table 2. Recommended Capacitor Vendors
The following guidelines should be followed when design-
ing a PCB layout for the LTC3217:
1. The Exposed Pad should be soldered to a large
copper plane that is connected to a solid, low imped-
ance ground plane using plated through-hole vias for
proper heat sinking and noise protection.
2. Input and output capacitors must be placed close to
the part.
3. The ?ying capacitors must be placed close to the
part. The traces from the pins to the capacitor pad
should be as wide as possible.
4. V BAT , CPO traces must be wide to minimize induc-
tance and handle high currents.
5. LED pads must be large and connected to other lay-
ers of metal to ensure proper LED heat sinking.
AVX
Kemet
Murata
Taiyo Yuden
Vishay
www.avxcorp.com
www.kemet.com
www.murata.com
www.t-yuden.com
www.vishay.com
Power Ef?ciency
To calculate the power ef?ciency ( η ) of a white LED
driver chip, the LED power should be compared to the
input power. The difference between these two numbers
represents lost power whether it is in the charge pump
or the current sources. Stated mathematically, the power
Layout Considerations and Noise
ef?ciency is given by:
Due to its high switching frequency and the transient
currents produced by the LTC3217, careful board layout
η=
P LED
P IN
(5)
is necessary. A true ground plane and short connections
to all capacitors will improve performance and ensure
proper regulation under all conditions.
The ?ying capacitor pins C1P, C2P, C1M and C2M will have
very high edge rate waveforms. The large dv/dt on these
pins can couple energy capacitively to adjacent PCB runs.
Magnetic ?elds can also be generated if the ?ying capacitors
The ef?ciency of the LTC3217 depends upon the mode in
which it is operating. Recall that the LTC3217 operates
as a pass switch, connecting V BAT to CPO, until dropout
is detected at the LED pin. This feature provides the op-
timum ef?ciency available for a given input voltage and
LED forward voltage. When it is operating as a switch, the
ef?ciency is approximated by:
= = LED
are not close to the LTC3217 (i.e., the loop area is large).
To decouple capacitive energy transfer, a Faraday shield
may be used. This is a grounded PCB trace between the
η=
P LED
P IN
( V LED ? I LED ) V
( V BAT ? I BAT ) V BAT
(6)
sensitive node and the LTC3217 pins. For a high quality
AC ground, it should be returned to a solid ground plane
that extends all the way to the LTC3217.
since the input current will be very close to the sum of
the LED currents.
3217fa
10
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3218EDDB#TRPBF | IC LED DRVR FLASH TORCH 10DFN |
| LTC3219EUD#PBF | IC LED DRIVR QVGA DISPLAY 20-QFN |
| LTC3220EPF#PBF | IC LED DRVR QVGA DISPLAY 28UTQFN |
| LTC3230EUD#PBF | IC LED DRIVR WHITE BCKLGT 20-QFN |
| LTC3452EUF#TRPBF | IC LED DRIVER PHOTO FLASH 20-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3218 | 制造商:LINER 制造商全称:Linear Technology 功能描述:400mA Single Wire Camera LED Charge Pump |
| LTC3218EDDB#PBF | 制造商:Linear Technology 功能描述:DP-Charge Pump/LED Driver, CUT TAPE 400mA, Single Wire Camera LED Charge Pump |
| LTC3218EDDB#TRMPBF | 功能描述:IC LED DRVR FLASH TORCH 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LTC3218EDDB#TRPBF | 功能描述:IC LED DRVR FLASH TORCH 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LTC3218EDDBPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:400mA Single Wire Camera LED Charge Pump |
发布紧急采购，3分钟左右您将得到回复。