参数资料
| 型号： | LTC3402EMS#TR |
| 厂商： | Linear Technology |
| 文件页数： | 8/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST SYNC ADJ 2A 10MSOP |
| 标准包装： | 2,500 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 2.6 V ~ 5.5 V |
| 输入电压： | 0.5 V ~ 5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 2MHz |
| 电流 - 输出： | 2A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 10-MSOP |
LTC3402
APPLICATIO S I FOR ATIO
DETAILED DESCRIPTION
The LTC3402 provides high efficiency, low noise power
for applications such as portable instrumentation. The
current mode architecture with adaptive slope compensa-
tion provides ease of loop compensation with excellent
transient load response. The low R DS(ON) , low gate charge
synchronous switches provide the pulse width modula-
tion control at high efficiency.
The Schottky diode across the synchronous PMOS switch
provides a lower drop during the break-before-make time
(typically 20ns) of the NMOS to PMOS transition. The
addition of the Schottky diode will improve efficiency (see
graph “Efficiency Loss Without Schottky vs Frequency”).
While the IC’s quiescent current is a low 38 μ A, high
efficiency is achieved at light loads when Burst Mode
operation is entered.
Low Voltage Start-Up
The LTC3402 is designed to start up at input voltages of
typically 0.85V. The device can start up under some load,
(see graph Start-Up vs Input Voltage). Once the output
voltage exceeds a threshold of 2.3V, then the IC powers
itself from V OUT instead of V IN . At this point, the internal
circuitry has no dependency on the input voltage, eliminat-
ing the requirement for a large input capacitor. The input
voltage can drop below 0.5V without affecting the opera-
tion, but the limiting factor for the application becomes the
availability of the power source to supply sufficient energy
to the output at the low voltages.
Low Noise Fixed Frequency Operation
Oscillator . The frequency of operation is set through a
resistor from the R t pin to ground where f = 3 ? 10 10 /R t . An
internally trimmed timing capacitor resides inside the IC.
The oscillator can be synchronized with an external clock
the error amplifier output to provide a peak current control
command for the PWM. The slope compensation in the IC
is adaptive to the input and output voltage. Therefore, the
converter provides the proper amount of slope compensa-
tion to ensure stability and not an excess causing a loss of
phase margin in the converter.
Error Amp . The error amplifier is a transconductance
amplifier with g m = 0.1ms. A simple compensation net-
work is placed from the V C pin to ground.
Current Limit . The current limit amplifier will shut the
NMOS switch off once the current exceeds its threshold.
The current amplifier delay to output is typically 50ns.
Zero Current Amp . The zero current amplifier monitors the
inductor current to the output and shuts off the synchro-
nous rectifier once the current is below 50mA, preventing
negative inductor current.
Antiringing Control . The anitringing control will place an
impedance across the inductor to damp the ringing on the
SW pin during discontinuous mode operation. The LC SW
ringing (L = inductor, C SW = capacitance on the switch pin)
is low energy, but can cause EMI radiation.
Burst Mode Operation
Burst Mode operation is when the IC delivers energy to the
output until it is regulated and then goes into a sleep mode
where the outputs are off and the IC is consuming only
38 μ A. In this mode, the output ripple has a variable
frequency component with load current and the steady
state ripple will be typically below 3%.
During the period where the device is delivering energy to
the output, the peak current will be equal to 1/6 the current
limit value and the inductor current will terminate at zero
current for each cycle. In this mode the maximum output
current is given by:
inserted on the MODE/SYNC pin. When synchronizing the
oscillator, the free running frequency must be set to
approximately 30% lower than the desired synchronized
I OUT ( MAXBURST ) ≈
V IN
6 ? V OUT
Amps
frequency. Keeping the sync pulse width below 2 μ s will
ensure that Burst Mode operation is disabled.
Current Sensing . Lossless current sensing converts the
peak current signal to a voltage to sum in with the internal
Burst Mode operation is user controlled by driving the
MODE/SYNC pin high to enable and low to disable. It is
recommended that Burst Mode operation be entered after
the part has started up.
slope compensation. This summed signal is compared to
3402fb
8
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3403EDD#TRPBF | IC REG BUCK SYNC ADJ 0.6A 8DFN |
| LTC3404MPMS8#PBF | IC REG BUCK SYNC ADJ 0.6A 8MSOP |
| LTC3405ES6#TRPBF | IC REG BUCK SYNC ADJ .3A SOT23-6 |
| LTC3406BES5-1.2#TRPBF | IC REG BUCK SYNC 1.2V TSOT23-5 |
| LTC3406ES5-1.8#TRPBF | IC REG BUCK SYNC 1.8V TSOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3403 | 制造商:LINER 制造商全称:Linear Technology 功能描述:1.5MHz, 600mA Synchronous Step-Down Regulator with Bypass Transistor |
| LTC3403EDD | 功能描述:IC REG BUCK SYNC ADJ 0.6A 8DFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3403EDD#PBF | 功能描述:IC REG BUCK SYNC ADJ 0.6A 8DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3403EDD#TR | 功能描述:IC REG BUCK SYNC ADJ 0.6A 8DFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3403EDD#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 0.6A 8DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
发布紧急采购，3分钟左右您将得到回复。