- 您现在的位置：买卖IC网 > PDF目录240305 > LTC3407AEDD (LINEAR TECHNOLOGY CORP) 1.25 A DUAL SWITCHING CONTROLLER, 1800 kHz SWITCHING FREQ-MAX, PDSO10 PDF资料下载
参数资料
| 型号： | LTC3407AEDD |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 1.25 A DUAL SWITCHING CONTROLLER, 1800 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封装： | 3 X 3 MM, PLASTIC, MO-229WEED-2, DFN-10 |
| 文件页数： | 2/16页 |
| 文件大小： | 263K |
| 代理商： | LTC3407AEDD |
LTC3407A
10
3407af
Power-On Reset
The POR pin is an open-drain output which pulls low when
either regulator is out of regulation. When both output
voltages are within
±8.5% of regulation, a timer is started
which releases POR after 216 clock cycles (about 44ms in
pulse skipping mode). This delay can be significantly
longer in Burst Mode operation with low load currents,
since the clock cycles only occur during a burst and there
could be milliseconds of time between bursts. This can be
bypassed by tying the POR output to the MODE/SYNC
input, to force pulse skipping mode during a reset. In
addition, if the output voltage faults during Burst Mode
sleep, POR could have a slight delay for an undervoltage
output condition and may not respond to an overvoltage
output. This can be avoided by using pulse skipping mode
instead. When either channel is shut down, the POR
output is pulled low, since one or both of the channels are
not in regulation.
Mode Selection & Frequency Synchronization
The MODE/SYNC pin is a multipurpose pin which provides
mode selection and frequency synchronization. Connect-
ing this pin to VIN enables Burst Mode operation, which
provides the best low current efficiency at the cost of a
higher output voltage ripple. When this pin is connected to
ground, pulse skipping operation is selected which pro-
vides the lowest output ripple, at the cost of low current
efficiency.
The LTC3407A can also be synchronized to another
LTC3407A by the MODE/SYNC pin. During synchroniza-
tion, the mode is set to pulse skipping and the top switch
turn-on is synchronized to the rising edge of the external
clock.
Checking Transient Response
The regulator loop response can be checked by looking at
the load transient response. Switching regulators take
several cycles to respond to a step in load current. When
a load step occurs, VOUT immediately shifts by an amount
equal to
ILOAD ESR, where ESR is the effective series
resistance of COUT. ILOAD also begins to charge or
discharge COUT generating a feedback error signal used by
the regulator to return VOUT to its steady-state value.
APPLICATIO S I FOR ATIO
WU
U
At worst, the ringing at the input can be large enough to
damage the part.
Since the ESR of a ceramic capacitor is so low, the input
and output capacitor must instead fulfill a charge storage
requirement. During a load step, the output capacitor must
instantaneously supply the current to support the load
until the feedback loop raises the switch current enough to
support the load. The time required for the feedback loop
to respond is dependent on the compensation and the
output capacitor size. Typically, 3-4 cycles are required to
respond to a load step, but only in the first cycle does the
output drop linearly. The output droop, VDROOP, is usually
about 3 times the linear drop of the first cycle. Thus, a good
place to start is with the output capacitor size of approxi-
mately:
C
I
fV
OUT
O
DROOP
≈
3
More capacitance may be required depending on the duty
cycle and load step requirements.
In most applications, the input capacitor is merely re-
quired to supply high frequency bypassing, since the
impedance to the supply is very low. A 10
F ceramic
capacitor is usually enough for these conditions.
Setting the Output Voltage
The LTC3407A develops a 0.6V reference voltage between
the feedback pin, VFB, and ground as shown in
Figure 1. The output voltage is set by a resistive divider
according to the following formula:
VV
R
OUT =+
06
1
2
1
.
Keeping the current small (<5
A) in these resistors maxi-
mizes efficiency, but making them too small may allow
stray capacitance to cause noise problems and reduce the
phase margin of the error amp loop.
To improve the frequency response, a feed-forward ca-
pacitor CF may also be used. Great care should be taken to
route the VFB line away from noise sources, such as the
inductor or the SW line.
相关PDF资料 |
PDF描述 |
|---|---|
| L9950XP | BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36 |
| LQS50A48-3V3REJ | 1-OUTPUT 200 W DC-DC REG PWR SUPPLY MODULE |
| LTC3809IDD-1#TR | 1 A SWITCHING CONTROLLER, 600 kHz SWITCHING FREQ-MAX, PQCC10 |
| LKP5660-6D3T | 2-OUTPUT 250 W AC-DC PWR FACTOR CORR MODULE |
| LKP5660-6ED4B1 | 2-OUTPUT 250 W AC-DC PWR FACTOR CORR MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3407AEDD#PBF | 功能描述:IC REG BUCK SYNC ADJ 1A DL 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3407AEDD#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 1A DL 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3407AEDD-2 | 制造商:Linear Technology 功能描述:Conv DC-DC Dual Step Down 2.5V to 5.5V 10-Pin DFN EP |
| LTC3407AEDD-2#PBF | 功能描述:IC REG BUCK SYNC ADJ 1A DL 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3407AEDD-2#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 1A DL 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。