- 您现在的位置：买卖IC网 > PDF目录20697 > LTC3445EUF#PBF (Linear Technology)IC REG TRPL BUCK/LINEAR 24-QFN PDF资料下载
参数资料
| 型号： | LTC3445EUF#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 14/24页 |
| 文件大小： | 475K |
| 描述： | IC REG TRPL BUCK/LINEAR 24-QFN |
| 标准包装： | 91 |
| 拓扑： | 降压（降压）（1），线性（LDO）（2） |
| 功能： | 任何功能 |
| 输出数： | 3 |
| 频率 - 开关： | 1.5MHz |
| 电压/电流 - 输出 1： | 0.85 V ~ 1.55 V，600mA |
| 电压/电流 - 输出 2： | 可调至0.6V，50mA |
| 电压/电流 - 输出 3： | 可调至0.6V，50mA |
| 带 LED 驱动器： | 无 |
| 带监控器： | 无 |
| 带序列发生器： | 无 |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 供应商设备封装： | 24-QFN 裸露焊盘（4x4） |
| 包装： | 管件 |
| 产品目录页面： | 1334 (CN2011-ZH PDF) |
14
LTC3445
3445fa
When V
CC1
rises above 2.8V, the PowerPaths LDO is
enabled and set to the lesser of 3V or V
CC1
. Once V
TRACK
is 3V or higher, it controls the PowerPaths LDO output
(V
CC
BATT) voltage to within 200mV of V
TRACK
. Note that
V
TRACK
needs to be less than or equal to V
CC1
.
When
V
TRACK
falls below 3V, V
CC1
is used to regulate the
PowerPaths LDO (V
CC
BATT) to 3V. When V
CC1
falls
below 2.4V, the PowerPath LDO is disconnected and
V
BACKUP
is connected to V
CC
BATT.
The PowerPaths fault detection circuit uses an open-drain
driver (BATTFAULT) to report when the main battery is
disconnected.
Figure 5 shows the different states of the PowerPath
circuits. Typically, V
BACKUP
is a coin cell; however, other
types of back up power supplies may be used.
General I
2
C Bus/SMBus Description
I
2
C Bus and SMBus are reasonably similar examples of
2-wire, bidirectional, serial communications busses. Call-
ing them 2-wire is not strictly accurate, as there is an
implied third wire, which is the ground line. Large ground
drops or spikes between the grounds of different parts on
the bus can interrupt or disrupt communications, as the
signals on the two wires are both inherently referenced to
a ground which is expected to be common to all parts on
the bus. Both bus types have one data line and one clock
line which are externally pulled to a high voltage when they
are not being controlled by a device on the bus. The
devices on the bus can only pull the data and clock lines
low, which makes it simple to detect if more than one
device is trying to control the bus; eventually, a device will
release a line and it will not pull high because another
device is still holding it low. Pull-ups for the data and clock
lines are usually provided by external discrete resistors,
but external current sources can also be used. Since there
are no dedicated lines to use to tell a given device if another
device is trying to communicate with it, each device must
have a unique address to which it will respond. The first
part of any communication is to send out an address on the
bus and wait to see if another device responds to it. After
a response is detected, meaningful data can be exchanged
between the parts.
Typically, one device will control the clock line at least
most of the time and will normally be sending data to the
other parts and polling them to send data back to it, and
this device is called the master. There can certainly be
more than one master, since there is an effective protocol
to resolve bus contentions, and non-master (slave) de-
vices can also control the clock to delay rising edges and
give themselves more time to complete calculations or
communications (clock stretching). Slave devices need to
OPERATIO
(refer to Figure 1)
Figure 6. Typical 2-Wire Serial I
2
C Waveforms
Figure 5
0V
2.4V
2.8V
3V
3.6V
4.2V
V
CC1
V
TRACK
3445 F05
V
BACKUP
BATTFAULT = 1
ADDRESS
START
CONDITION
R/W
1-7
S
SCL
SDA
8
9
1-7
1-7
8
9
3445 F06
8
9
STOP
CONDITION
P
ACK
ACK
ACK
DATA
DATA
I
2
C OPERATION
" Simple 2-wire interface
" Multiple devices on same bus
" Idle bus must have SDA and SCL lines high
" LTC3445 is read/write
" Master controls bus
" Devices listen for unique address that precedes data
相关PDF资料 |
PDF描述 |
|---|---|
| RMM43DRTH-S13 | CONN EDGECARD 86POS .156 EXTEND |
| RSO-243.3DZ/H3 | CONV DC/DC 1W 9-36VIN +/-3.3VOUT |
| RSO-0505D/H3 | CONV DC/DC 1W 4.5-9VIN +/-05VOUT |
| RSA44DRMI | CONN EDGECARD 88POS .125 SQ WW |
| EBC18DCAI-S189 | CONN EDGECARD 36POS R/A .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3446 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic Buck Regulator with Dual VLDO Regulators |
| LTC3446EDE | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic Buck Regulator with Dual VLDO Regulators |
| LTC3446EDE#PBF | 功能描述:IC REG TRPL BCK/LINEAR 14-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| LTC3446EDE#TRPBF | 功能描述:IC REG TRPL BCK/LINEAR 14-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| LTC3446EDE-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic Buck Regulator with Dual VLDO Regulators |
发布紧急采购，3分钟左右您将得到回复。