- 您现在的位置：买卖IC网 > Datasheet目录338 > LTC3454EDD#TRPBF (Linear Technology)IC LED DRIVER PHOTO FLASH 10-DFN Datasheet资料下载
参数资料
| 型号： | LTC3454EDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/12页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER PHOTO FLASH 10-DFN |
| 标准包装： | 2,500 |
| 拓扑： | PWM，降压（降压），升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光，闪灯/白光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 900kHz ~ 1.15MHz |
| 电源电压： | 2.7 V ~ 5.5 V |
| 输出电压： | 5.15V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-DFN（3x3） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
LTC3454
APPLICATIONS INFORMATION
V IN ( MIN ) 2 ? ( V OUT V IN ( MIN ) ) ? 100 %
I OUT ( MAX ) ? ( V OUT IN ( MIN ) ) ? 100%
COMPONENT SELECTION
Inductor Selection
The high frequency operation of the LTC3454 allows the
use of small surface mount inductors. The inductor cur-
rent ripple is typically set to 20% to 40% of the maximum
average inductor current. For a given ripple the inductance
term in boost mode is:
–
L >
f ? I OUT ( MAX ) ? % Ripple ? V OUT 2
and in buck mode is:
L > ( V IN ( MAX ) – V OUT ) ? V OUT ? 100 %
f ? V IN ( MAX ) ? % Ripp l e ? I OUT
where f = operating frequency, Hz
%Ripple = allowable inductor current ripple, %
V IN(MIN) = minimum input voltage, V
V IN(MAX) = maximum input voltage, V
V OUT = output voltage, V
I OUT(MAX) = maximum output load current
For high ef?ciency, choose an inductor with a high fre-
quency core material, such as ferrite, to reduce core loses.
The inductor should have low ESR (equivalent series
resistance) to reduce the I 2 R losses, and must be able
to handle the peak inductor current without saturating.
Molded chokes or chip inductors usually do not have
enough core to support peak inductor currents >1A. To
minimize radiated noise, use a toroid, pot core or shielded
bobbin inductor. For white LED application, a 4.7μH/5μH
inductor value is recommended. See Table 1 for a list of
component suppliers.
Table 1. Inductor Vendor Information
SUPPLIER WEB SITE
Coilcraft www.coilcraft.com
Input Capacitor Selection
Since the V IN pin is the supply voltage for the IC it is recom-
mended to place at least a 2.2μF, low ESR bypass capacitor
to ground. See Table 2 for a list of component suppliers.
Table 2. Capacitor Vendor Information
SUPPLIER WEB SITE
AVX www.avxcorp.com
Sanyo www.sanyovideo.com
Taiyo Yuden www.t-yuden.com
TDK www.component.tdk.com
Output Capacitor Selection
The bulk value of the capacitor is set to reduce the ripple
due to charge into the capacitor each cycle. The steady-
state ripple due to charge is given by:
– V %
% Ripple _ Boost =
C OUT ? V OUT 2 ? f
% Ripple _ Buck = ( V IN ( MAX ) – V OUT ) ? 1 00 %
8 ? V IN ( MAX ) ? f 2 ? L ? C OUT
where C OUT = output ?lter capacitor, F
The output capacitance is usually many times larger in
order to handle the transient response of the converter. For
a rule of thumb, the ratio of operating frequency to unity-
gain bandwidth of the converter is the amount the output
capacitance will have to increase from the above calcula-
tions in order to maintain desired transient response.
The other component of ripple is due to ESR (equivalent
series resistance) of the output capacitor. Low ESR ca-
pacitors should be used to minimize output voltage ripple.
For surface mount applications, Taiyo Yuden, TDK, AVX
ceramic capacitors, AVX TPS series tantalum capacitors
or Sanyo POSCAP are recommended. For the white LED
application, a 10μF capacitor value is recommended. See
Table 2 for a list of component suppliers.
Cooper/Coiltronics
Murata
Sumida
Toko
Vishay-Dale
www.cooperet.com
www.murata.com
www.japanlink.com/sumida
www.toko.com
www.vishay.com
Optional Schottky Diodes
Schottky diodes across the synchronous switches B and
D are not required, but provide a lower drop during the
break-before-make time (typically 20ns) of the NMOS to
PMOS transition, improving ef?ciency. Use a Schottky
3454fa
9
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3490EDD#PBF | IC LED DRIVER PHOTO FLASH 8-DFN |
| LTC3783EFE#PBF | IC LED DRVR PWM CONTROL 16-TSSOP |
| LV5026MC-AH | IC LED DRIVER 1CH HV 10SOIC |
| LV5213LP-TE-L-E | IC LED DVR 3CH CELL PHONE VCT16 |
| LV5216CS-TE-L-E | IC LED DRIVER 10CH CELL 36WLP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3455 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency Battery Charger/USB Power Manager |
| LTC3455EUF | 功能描述:IC CONV DC/DC DUAL USBBATT 24QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| LTC3455EUF#PBF | 功能描述:IC CONV DC/DC DUAL USBBATT 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| LTC3455EUF#TR | 功能描述:IC CONV DC/DC DUAL USBBATT 24QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| LTC3455EUF#TRPBF | 功能描述:IC CONV DC/DC DUAL USBBATT 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
发布紧急采购，3分钟左右您将得到回复。