- 您现在的位置：买卖IC网 > PDF目录1829 > LTC3520EUF#PBF (Linear Technology)IC REG BUCK BOOST SYNC ADJ 24QFN PDF资料下载
参数资料
| 型号： | LTC3520EUF#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK BOOST SYNC ADJ 24QFN |
| 标准包装： | 91 |
| 类型： | 降压（降压），升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 0.8 V ~ 5.5 V |
| 输入电压： | 2.2 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 100kHz ~ 2MHz |
| 电流 - 输出： | 600mA，1A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 24-QFN 裸露焊盘（4x4） |
| 产品目录页面： | 1334 (CN2011-ZH PDF) |
LTC3520
PIN FUNCTIONS
SV IN (Pin 1): Small Signal Power Supply Connection.
This pin is used to power the internal circuitry of the
LTC3520. This pin should be bypassed using a 0.1μF or
larger ceramic capacitor placed as close as possible to
the pin with a short return path to ground. Pins PV IN1 ,
PV IN2 , PV IN3 , and SV IN must be connected together in
the application circuit.
A OUT (Pin 2): Uncommitted Ampli?er Output. This pin
should be connected to the base of an external PNP
transistor for use as an LDO regulator. If used as a
battery-good indicator or for supply sequencing, this pin
is the comparator output.
A IN (Pin 3): Non-Inverting Input to the Uncommitted
Ampli?er. In LDO applications, this pin is connected to
the LDO feedback voltage.
R T (Pin 4): Programs the Frequency of the Internal Oscilla-
tor. This pin must be tied to ground via an external resistor.
The value of the resistor controls the oscillator frequency.
For details on choosing the value of this resistor see the
Applications Information section of this datasheet.
PWM1 (Pin 5): Logic Input Used to Choose Between Burst
and PWM Mode for the Buck-Boost Converter. This pin
cannot be left ?oating.
PWM1 = Low: The buck-boost converter will operate in
variable frequency mode to improve ef?ciency at light
loads. In this mode, the LTC3520 can only supply a
reduced load current (typically 50mA).
PWM1 = High: The buck-boost converter will remain
in low noise, ?xed frequency PWM mode at all load
currents.
SD1 (Pin 6): Buck-Boost Active-Low Shutdown Pin. Forc-
ing this pin above 1.4V enables the buck-boost converter.
Forcing this pin below 0.4V disables the buck-boost
converter. This pin cannot be left ?oating.
SD2 (Pin 7): Buck Active-Low Shutdown Pin. Forcing
this pin above 1.4V enables the buck converter. Forcing
this pin below 0.4V disables the buck converter. This pin
cannot be left ?oating.
SD3 (Pin 8): Uncommitted Ampli?er Active-Low Shutdown
ampli?er. Forcing this pin below 0.4V disables the uncom-
mitted ampli?er. This pin cannot be left ?oating.
PV IN2 (Pin 9): High Current Power Supply Connection
Used to Supply the Buck Converter PMOS Power Device.
This pin should be bypassed by a 22μF or larger ceramic
capacitor. The bypass capacitor should be placed as close
to the pin as possible and should have a short return path
to ground. Pins PV IN1 , PV IN2 , PV IN3 , and SV IN must be
connected together in the application circuit.
SW2 (Pin 10): Buck Converter Switch Node. This pin must
be connected to one side of the buck inductor.
PGND2 (Pin 11): High Current Ground Connection for the
Buck Converter N-Channel MOSFET Power Device. The
PCB trace connecting this pin to ground should be made
as short and wide as possible.
PWM2 (Pin 12): Burst/PWM Mode Control Pin for the Buck
Converter. This pin can be used in the following ways:
PWM2 forced high: With PWM2 forced high, the buck
converter will be forced into low noise ?xed frequency
operation. The buck converter will remain in this mode
unless the load current is low enough that the minimum
on-time is reached at which point the converter will
begin pulse-skipping to maintain regulation.
PWM2 connected to ground via resistor: PWM2 can be
connected to ground through a resistor to control the
load current at which Burst Mode operation is entered
and exited. Larger resistor values will cause the buck
converter to enter Burst Mode operation at lower load
currents and will result in lower output voltage ripple
in Burst Mode operation. Smaller resistor values will
cause Burst Mode operation to be entered at higher load
currents and the Burst Mode ripple will be larger.
PWM2 forced low: With PWM2 forced to ground, the
buck converter will operate in Burst Mode operation for
all but the highest load currents. Generally, this mode of
operation is utilized to force the buck converter into Burst
Mode operation when it is known that the load current
will be relatively low (under 75mA) or in applications
that are not sensitive to output voltage ripple.
Pin. Forcing this pin above 1.4V enables the uncommitted
3520fa
8
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3521IFE#TRPBF | IC REG BUCK BST SYNC ADJ 20TSSOP |
| LTC3522EUD#TRPBF | IC REG BUCK BOOST SYNC ADJ 16QFN |
| LTC3523EUD-2#TRPBF | IC REG BUCK BOOST SYNC ADJ 16QFN |
| LTC3525ESC6-3.3#TRPBF | IC REG BST SYNC 3.3V 0.4A SC70-6 |
| LTC3526BEDC#TRPBF | IC REG BOOST SYNC ADJ 0.5A 6DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3520EUF-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Synchronous 1A Buck-Boost and 600mA Buck Converters |
| LTC3520IUF#PBF | 功能描述:IC REG BUCK BOOST SYNC ADJ 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3520IUF#TRPBF | 功能描述:IC REG BUCK BOOST SYNC ADJ 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3521 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Wide VIN, 1A Buck-Boost DC/DC and Dual 600mA Buck DC/DC Converters |
| LTC3521EFE#PBF | 功能描述:IC REG BUCK BST SYNC ADJ 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
发布紧急采购，3分钟左右您将得到回复。