- 您现在的位置：买卖IC网 > PDF目录1830 > LTC3523EUD-2#TRPBF (Linear Technology)IC REG BUCK BOOST SYNC ADJ 16QFN PDF资料下载
参数资料
| 型号： | LTC3523EUD-2#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK BOOST SYNC ADJ 16QFN |
| 标准包装： | 2,500 |
| 类型： | 降压（降压），升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 0.62 V ~ 5.5 V |
| 输入电压： | 1.8 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 2.4MHz |
| 电流 - 输出： | 400mA，600mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 16-QFN-EP（3x3） |
LTC3523/LTC3523-2
OPERATION
The LTC3523 and LTC3523-2 are synchronous step-up and
step-down converters housed in a 16-pin QFN package.
Operating from inputs down to 1.8V, the devices feature
?xed frequency, current mode PWM control for exceptional
line and load regulation and transient response. With
low R DS(ON) and internal MOSFET switches, the devices
maintain high ef?ciency over a wide range of load cur-
rent. Operation can be best understood by referring to
the Block Diagram.
Soft-Start
Both the step-up and step-down converters on the LTC3523
/LTC3523-2 provide soft-start. The soft-start time is typi-
cally 500μs. The soft-start function resets in the event of
a commanded shutdown or thermal shutdown.
Oscillator
The frequency of operation is set by an internal oscilla-
tor to a nominal 1.2MHz for the LTC3523 and nominal
2.4MHz for the LTC3523-2. The oscillator is shared by
both converters.
Shutdown
The step-up and the step-down converters have inde-
pendent shutdown pins. To shut down a converter, pull
SHDNx below 0.35V. To enable a converter, pull SHDNx
above 1.0V.
Error Ampli?ers
Power converter control loop compensation is provided
internally for each converter. The noninverting input is
internally connected to the 1.2V reference for the step-up
and 0.6V for the step-down. The inverting input is connected
to the respective FBx for both converters. Internal clamps
limit the minimum and maximum error amp output voltage
for improved large signal transient response. A voltage
divider from V OUT to ground programs the output voltage
via the respective FBx pins from 1.8V to 5.25V for the step-
up and 0.615V to 5.5V for the step-down. From the Block
Diagram the design equation for programming the output
PWM Comparators
The PWM comparators are used to compare the converters
external inductor current to the current commanded by
the error ampli?ers. When the inductor current reaches
the current commanded by the error ampli?er the induc-
tor charging cycle is terminated and the recti?cation cycle
commences.
Current Limit
The current limit comparator shuts off the N-channel switch
for the step-up and P-channel switch for the step-down
once its current limit threshold is reached. The current
limit comparator delay to output is typically 40ns. Peak
switch current is limited to approximately 1000mA for
the step-up and 650mA for the step-down independent
of input or output voltage.
Zero Current Comparator
The zero current comparator monitors the inductor cur-
rent to the output and shuts off the synchronous recti?er
once this current reduces to approximately 20mA. This
prevents the inductor current from reversing in polarity
improving ef?ciency at light loads.
Power Good Comparator
Both converters have independent open drain power good
comparators which monitor the output voltage via their
respective FBx pins. The comparator output will allow the
PGOODx to be pulled up high when the output voltage
(V OUT ) has exceeded 91% of it ?nal value. If the output
voltage decreases below 91%, the comparator will pull
the PGOODx pin to ground. The step-up comparator has
3.3% of hysteresis and the step-down has 6.6% relative
to FBx voltage for added noise immunity.
Step-Down Overvoltage Comparator
The step-down overvoltage comparator guards against
transient overshoots greater than 10% of the output volt-
age by turning the P-channel switch off until the transient
has subsided.
voltages is V OUT = 1.2V ? [1 + (R1/R2)] for the step-up and
V OUT = 0.6V ? [1 + (R3/R4)] for the step-down.
3523fb
8
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3525ESC6-3.3#TRPBF | IC REG BST SYNC 3.3V 0.4A SC70-6 |
| LTC3526BEDC#TRPBF | IC REG BOOST SYNC ADJ 0.5A 6DFN |
| LTC3527EUD-1#TRPBF | IC REG BOOST SYNC ADJ DL 16QFN |
| LTC3528EDDB#TRPBF | IC REG BOOST SYNC ADJ 1A 8DFN |
| LTC3529EDCB#TRPBF | IC REG BOOST SYNC 5V 1.5A 8DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3523EUD-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Synchronous 600mA Step-Up and 400mA Step-Down DC/DC Converters |
| LTC3523EUD-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Synchronous 600mA Step-Up and 400mA Step-Down DC/DC Converters |
| LTC3524 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Adjustable TFT Bias Supply with WLED Driver |
| LTC3524EUF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Adjustable TFT Bias Supply with WLED Driver |
| LTC3524EUF#PBF | 功能描述:IC TFT BIAS SUPPLY ADJ 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
发布紧急采购，3分钟左右您将得到回复。