- 您现在的位置：买卖IC网 > PDF目录14161 > LTC3526BEDC#TRMPBF (Linear Technology)IC REG BOOST SYNC ADJ 0.5A 6DFN PDF资料下载
参数资料
| 型号： | LTC3526BEDC#TRMPBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST SYNC ADJ 0.5A 6DFN |
| 标准包装： | 500 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.6 V ~ 5.25 V |
| 输入电压： | 0.5 V ~ 5 V |
| PWM 型： | 电流模式，Burst Mode? |
| 频率 - 开关： | 1MHz |
| 电流 - 输出： | 500mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-WFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 6-DFN-EP（2x2） |
LTC3526/LTC3526B
OPERATION
(Refer to Block Diagram)
when this current reduces to approximately 30mA. This
prevents the inductor current from reversing in polarity,
improving efficiency at light loads.
Synchronous Rectifier
To control inrush current and to prevent the inductor
current from running away when V OUT is close to V IN , the
P-channel MOSFET synchronous rectifier is only enabled
when V OUT > (V IN + 0.24V).
Anti-Ringing Control
The anti-ringing control connects a resistor across the
inductor to prevent high frequency ringing on the SW pin
during discontinuous current mode operation. Although
the ringing of the resonant circuit formed by L and C SW
(capacitance on SW pin) is low energy, it can cause EMI
radiation.
Output Disconnect
The LTC3526/LTC3526B are designed to allow true output
disconnect by eliminating body diode conduction of the
internal P-channel MOSFET rectifier. This allows for V OUT
to go to zero volts during shutdown, drawing no current
from the input source. It also allows for inrush current
limiting at turn-on, minimizing surge currents seen by the
input supply. Note that to obtain the advantages of output
disconnect, there must not be an external Schottky diode
connected between the SW pin and V OUT . The output dis-
connect feature also allows V OUT to be pulled high, without
any reverse current into a battery connected to V IN .
Thermal Shutdown
If the die temperature exceeds 160°C, the LTC3526/
LTC3526B will go into thermal shutdown. All switches
will be off and the soft-start capacitor will be discharged.
The device will be enabled again when the die temperature
drops by about 15°C.
Burst Mode OPERATION
The LTC3526 will automatically enter Burst Mode opera-
tion at light load and return to fixed frequency PWM mode
when the load increases. Refer to the Typical Performance
Characteristics to see the output load Burst Mode thresh-
old current vs V IN . The load current at which Burst Mode
operation is entered can be changed by adjusting the
inductor value. Raising the inductor value will lower the
load current at which Burst Mode operation is entered.
In Burst Mode operation, the LTC3526 still switches at a
fixed frequency of 1MHz, using the same error amplifier
and loop compensation for peak current mode control.
This control method eliminates any output transient
when switching between modes. In Burst Mode opera-
tion, energy is delivered to the output until it reaches the
nominal regulation value, then the LTC3526 transitions to
sleep mode where the outputs are off and the LTC3526
consumes only 9μA of quiescent current from V OUT . When
the output voltage droops slightly, switching resumes.
This maximizes efficiency at very light loads by minimizing
switching and quiescent losses. Burst Mode output voltage
ripple, which is typically 1% peak-to-peak, can be reduced
by using more output capacitance (10μF or greater), or
with a small capacitor (10pF to 50pF) connected between
V OUT and FB.
As the load current increases, the LTC3526 will automati-
cally leave Burst Mode operation. Note that larger output
capacitor values may cause this transition to occur at lighter
loads. Once the LTC3526 has left Burst Mode operation and
returned to normal operation, it will remain there until the
output load is reduced below the burst threshold.
Burst Mode operation is inhibited during start-up and soft-
start and until V OUT is at least 0.24V greater than V IN .
The LTC3526B features continuous PWM operation at
1MHz. At very light loads, the LTC3526B will exhibit
pulse-skip operation.
3526bfd
相关PDF资料 |
PDF描述 |
|---|---|
| RSM15DTBI | CONN EDGECARD 30POS R/A .156 SLD |
| HMC10DRYI | CONN EDGECARD 20POS DIP .100 SLD |
| LTC1682CMS8#TRPBF | IC REG MULTI CONFIG ADJ 8MSOP |
| GSC20DRTS | CONN EDGECARD 40POS DIP .100 SLD |
| LTC1682CMS8#TR | IC REG MULTI CONFIG ADJ 8MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3526BEDC-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:500mA 1MHz Synchronous Step-Up DC/DC Converters in 2mm × 2mm DFN |
| LTC3526EDC | 制造商:LINER 制造商全称:Linear Technology 功能描述:500mA 1MHz Synchronous Step-Up DC/DC Converters in 2mm X 2mm DFN |
| LTC3526EDC#PBF | 制造商:Linear Technology 功能描述:IC SYNC STEP-UP DC/DC CONVERTER DFN-6 制造商:Linear Technology 功能描述:IC, SYNC STEP-UP DC/DC CONVERTER, DFN-6 制造商:Linear Technology 功能描述:IC, SYNC STEP-UP DC/DC CONVERTER, DFN-6; Primary Input Voltage:6V; No. of Outputs:1; Output Voltage:5.25V; Output Current:500mA; No. of Pins:6; Operating Temperature Min:-40C; Operating Temperature Max:85C; MSL:MSL 1 - Unlimited ;RoHS Compliant: Yes |
| LTC3526EDC#TRMPBF | 功能描述:IC REG BOOST SYNC ADJ 0.5A 6DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3526EDC#TRPBF | 功能描述:IC REG BOOST SYNC ADJ 0.5A 6DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
发布紧急采购，3分钟左右您将得到回复。