- 您现在的位置：买卖IC网 > PDF目录69007 > LTC3528EDDB#TRM (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, 1300 kHz SWITCHING FREQ-MAX, PDSO8 PDF资料下载
参数资料
| 型号： | LTC3528EDDB#TRM |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, 1300 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封装： | 3 X 2 MM, 0.75 MM HEIGHT, PLASTIC, MO-229WECD-1, DFN-8 |
| 文件页数： | 16/16页 |
| 文件大小： | 316K |
| 代理商： | LTC3528EDDB#TRM |
LTC3528/LTC3528B
9
3528f
Zero Current Comparator
The zero current comparator monitors the inductor cur-
rent to the output and shuts off the synchronous rectier
when this current reduces to approximately 20mA. This
prevents the inductor current from reversing in polarity,
improving efciency at light loads.
Synchronous Rectier
To control inrush current and to prevent the inductor
current from running away when VOUT is close to VIN, the
P- channel MOSFET synchronous rectier is only enabled
when VOUT > (VIN + 0.24V).
Anti-Ringing Control
The anti-ringing control connects a resistor across the
inductor to prevent high frequency ringing on the SW pin
during discontinuous current mode operation. The ringing
of the resonant circuit formed by L and CSW (capacitance
on SW pin) is low energy, but can cause EMI radiation.
Output Disconnect
The LTC3528/LTC3528B is designed to allow true output
disconnect by eliminating body diode conduction of the
internal P-channel MOSFET rectier. This allows for VOUT
to go to zero volts during shutdown, drawing no current
from the input source. It also enables inrush current limiting
at turn-on, minimizing surge currents seen by the input
supply. Note that to obtain the advantages of output discon-
nect, a Schottky diode cannot be connected between SW
and VOUT. The output disconnect feature also allows VOUT
to be forced above the programmed regulation voltage,
without any reverse current into a battery on VIN.
Thermal Shutdown
If the die temperature exceeds 160°C, the LTC3528/
LTC3528B will enter thermal shutdown. All switches will be
turned off and the soft-start capacitor will be discharged.
The device will be enabled again when the die temperature
drops by approximately 15°C.
Burst Mode OPERATION
The LTC3528 will automatically enter Burst Mode operation
at light load current and return to xed frequency PWM
mode when the load increases. Refer to the Typical Perfor-
mance Characteristics to see the output load Burst Mode
threshold vs VIN. The load at which Burst Mode operation
is entered can be changed by adjusting the inductor value.
Raising the inductor value will lower the load current at
which Burst Mode operation is entered.
In Burst Mode operation, the LTC3528 continues switch-
ing at a xed frequency of 1MHz, using the same error
amplier and loop compensation for peak current mode
control. This control method minimizes output transients
when switching between modes. In Burst Mode opera-
tion, energy is delivered to the output until it reaches the
nominal regulated value, then the LTC3528 transitions to
sleep mode where the outputs are off and the LTC3528
consumes only 12μA of quiescent current from VOUT. Once
the output voltage has drooped slightly, switching resumes
again. This maximizes efciency at very light loads by
minimizing switching and quiescent current losses. Burst
Mode output ripple, which is typically 1% peak-to-peak,
can be reduced by using more output capacitance (10μF
or greater).
As the load current increases, the LTC3528 automatically
leaves Burst Mode operation. Note that larger output ca-
pacitor values may cause this transition to occur at lighter
loads. The regulator will also leave Burst Mode operation if
a load transient occurs which causes the inductor current
to repeatedly reach current limit. Once the LTC3528 has
left Burst Mode operation and returned to normal opera-
tion, it will remain there until the output load is reduced
below the Burst threshold.
Burst Mode operation is inhibited during start-up and
until soft-start is done and VOUT is at least 0.24V greater
than VIN.
The LTC3528B features continuous PWM operation at
1MHz. At very light loads, the LTC3528B will exhibit
pulse-skip operation.
OPERATION (Refer to Block Diagram)
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3542EDC-1#PBF | SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO6 |
| LTC3547BIDDB#TRM | 0.7 A DUAL SWITCHING CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PDSO8 |
| LTC3547BEDDB-1#PBF | 0.7 A DUAL SWITCHING CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PDSO8 |
| LTC3547BIDDB#PBF | 0.7 A DUAL SWITCHING CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PDSO8 |
| LTC3560ES6 | 2.1 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3528EDDB-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:1A, 1MHz Synchronous Step-Up DC/DC Converters in 3mm × 2mm DFN |
| LTC3529EDCB#PBF | 制造商:Linear Technology 功能描述:IC SYNC STEP-UP DC/DC CONVERTER DFN-8 制造商:Linear Technology 功能描述:DP-SWREG/Monolithic, Cut Tape 1.5A, 2.35MHz Step-Up DC/DC Converter in 2mm x 3mm 制造商:Linear Technology 功能描述:IC, SYNC STEP-UP DC/DC CONVERTER, DFN-8, Primary Input Voltage:5.25V, No. of Outputs:1, Output Voltage:5V, Output Current:500mA, No. of Pins:8, Operating Temperature Min:-40C, Operating Temperature Max:85C, MSL:MSL 1 - Unlimited , RoHS Compliant: Yes |
| LTC3529EDCB#TRMPBF | 功能描述:IC REG BOOST SYNC 5V 1.5A 8DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3529EDCB#TRPBF | 功能描述:IC REG BOOST SYNC 5V 1.5A 8DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3530 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Wide Input Voltage Synchronous Buck-Boost DC/DC Converter |
发布紧急采购，3分钟左右您将得到回复。