- 您现在的位置：买卖IC网 > PDF目录14830 > LTC3530EDD#PBF (Linear Technology)IC REG BUCK BOOST SYNC ADJ 10DFN PDF资料下载
参数资料
| 型号： | LTC3530EDD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK BOOST SYNC ADJ 10DFN |
| 标准包装： | 121 |
| 类型： | 降压（降压），升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.8 V ~ 5.25 V |
| 输入电压： | 1.8 V ~ 5.5 V |
| PWM 型： | Burst Mode? |
| 频率 - 开关： | 300kHz ~ 2MHz |
| 电流 - 输出： | 600mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 10-DFN（3x3） |
| 产品目录页面： | 1334 (CN2011-ZH PDF) |
LTC3530
APPLICATIONS INFORMATION
The output capacitance is usually many times larger than
the minimum value in order to handle the transient response
requirements of the converter. For a rule of thumb, the ratio
of the operating frequency to the unity-gain bandwidth of
the converter is the amount the output capacitance will
have to increase from the above calculations in order to
maintain the desired transient response.
The other component of ripple is due to the ESR (equiva-
lent series resistance) of the output capacitor. Low ESR
capacitors should be used to minimize output voltage
ripple. For surface mount applications, Taiyo Yuden or
TDK ceramic capacitors, AVX TPS series tantalum capaci-
tors or Sanyo POSCAP are recommended. See Table 2 for
contact information.
Input Capacitor Selection
Since V IN is the supply voltage for the IC, as well as the
input to the power stage of the converter, it is recommended
to place at least a 10μF, low ESR ceramic bypass capaci-
tor close to the V IN and GND pins. It is also important to
minimize any stray resistance from the converter to the
battery or other power source.
Optional Schottky Diodes
Schottky diodes across the synchronous switches B and
D are not required (V OUT < 4.3V), but provide a lower drop
during the break-before-make time (typically 15ns) improv-
ing ef?ciency. Use a surface mount Schottky diode such as
an MBRM120T3 or equivalent. Do not use ordinary recti?er
diodes, since the slow recovery times will compromise
ef?ciency. For applications with an output voltage above
4.3V, a Schottky diode is required from SW2 to V OUT .
Output Voltage < 1.8V
The LTC3530 can operate as a buck converter with output
voltages as low as 0.4V. Synchronous switch D is powered
from V OUT and the R DS(ON) will increase at low output volt-
ages, therefore a Schottky diode is required from SW2 to
V OUT to provide the conduction path to the output. Note
that Burst Mode operation is inhibited at output voltages
below 1V typical. Note also that if V OUT is less than 1V,
the current limit will be 670mA (typ).
Output Voltage > 4.3V
A Schottky diode from SW2 to V OUT is required for output
voltages over 4.3V. The diode must be located as close to
the pins as possible in order to reduce the peak voltage on
SW2 due to the parasitic lead and trace inductance.
Input Voltage > 4.5V
For applications with input voltages above 4.5V which
could exhibit an overload or short-circuit condition, a
2 Ω /1nF series snubber is required between SW1 and
GND. A Schottky diode from SW1 to V IN should also be
added as close to the pins as possible. For the higher input
voltages, V IN bypassing becomes more critical; therefore,
a ceramic bypass capacitor as close to the V IN and GND
pins as possible is also required.
Operating Frequency Selection
Higher operating frequencies allow the use of a smaller
inductor and smaller input and output ?lter capacitors,
thus reducing board area and component height. How-
ever, higher operating frequencies also increase the IC’s
total quiescent current due to the gate charge of the four
switches, as given by:
Buck:
Boost:
Iq = (0.6 ? V IN ? f) mA
Iq = [0.8 ? (V IN + V OUT ) ? f] mA
Buck/Boost: Iq = [f ? (1.4 ? V IN + 0.4 ? V OUT )] mA
Table 2. Capacitor Vendor Information
SUPPLIER
AVX
Murata
Sanyo
Taiyo Yuden
TDK
PHONE
(803) 448-9411
(814) 237-1431, (800) 831-9172
(619) 661-6322
(408) 573-4150
(847) 803-6100
FAX
(803) 448-1943
(814) 238-0409
(619) 661-1055
(408) 573-4159
(847) 803-6296
WEB SITE
www.avxcorp.com
www.murata.com
www.sanyovideo.com
www.t-yuden.com
www.component.tdk.com
3530fb
11
相关PDF资料 |
PDF描述 |
|---|---|
| MXD1817UR22+T | IC MPU RESET CIRC 2.18V SOT23-3 |
| LT1614CMS8#PBF | IC REG INV ADJ 0.5A 8MSOP |
| EBM24DTBT-S189 | CONN EDGECARD 48POS R/A .156 SLD |
| LTC3401EMS#PBF | IC REG BOOST SYNC ADJ 1A 10MSOP |
| MXD1817UR29+T | IC MPU RESET CIRC 2.88V SOT23-3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3530EDD-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Wide Input Voltage Synchronous Buck-Boost DC/DC Converter |
| LTC3530EMS | 制造商:LINER 制造商全称:Linear Technology 功能描述:Wide Input Voltage Synchronous Buck-Boost DC/DC Converter |
| LTC3530EMS#PBF | 功能描述:IC REG BUCK BST SYNC 0.6A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3530EMS#TRPBF | 功能描述:IC REG BUCK BST SYNC 0.6A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3530EMS-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Wide Input Voltage Synchronous Buck-Boost DC/DC Converter |
发布紧急采购，3分钟左右您将得到回复。