- 您现在的位置：买卖IC网 > PDF目录1830 > LTC3535EDD#PBF (Linear Technology)IC REG BST SYNC ADJ 0.55A 12DFN PDF资料下载
参数资料
| 型号： | LTC3535EDD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BST SYNC ADJ 0.55A 12DFN |
| 特色产品： | Energy Harvesting Power Products |
| 标准包装： | 121 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 1.5 V ~ 5.25 V |
| 输入电压： | 0.5 V ~ 5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 1MHz |
| 电流 - 输出： | 550mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-WFDFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 12-DFN |
| 产品目录页面： | 1335 (CN2011-ZH PDF) |
LTC3535
OPERATION
(Refer to Block Diagram)
Burst Mode OPERATION
Each channel of the LTC3535 will enter Burst Mode
operation at light load current and return to fixed frequency
PWM mode when the load increases. Refer to the Typical
Performance Characteristics to see the output load Burst
Mode threshold current vs V IN . The load current at which
Burst Mode operation is entered can be changed by
adjusting the inductor value. Raising the inductor value
will lower the load current at which Burst Mode operation
is entered.
In Burst Mode operation, the LTC3535 still switches at a
fixed frequency of 1MHz, using the same error amplifier
and loop compensation for peak current mode control.
This control method eliminates any output transient when
switching between modes. In Burst Mode operation,
energy is delivered to the output until it reaches the
nominal regulation value, then the LTC3535 transitions
to sleep mode where the outputs are off and the LTC3535
consumes only 9μA of quiescent current from V OUT for
APPLICATIONS INFORMATION
V IN > V OUT OPERATION
The LTC3535 will maintain voltage regulation even when
the input voltage is above the desired output voltage. Note
that the efficiency is much lower in this mode, and the
maximum output current capability will be less. Refer to
the Typical Performance Characteristics.
SHORT-CIRCUIT PROTECTION
each channel. When the output voltage droops slightly,
switching resumes. This maximizes efficiency at very light
loads by minimizing switching and quiescent losses. Burst
Mode output voltage ripple, which is typically 1% peak-to-
peak, can be reduced by using more output capacitance
(10μF or greater), or with a small capacitor (10pF to 50pF)
connected between V OUT and FB.
As the load current increases, the LTC3535 will automati-
cally leave Burst Mode operation. Note that larger output
capacitor values may cause this transition to occur at
lighter loads. Once the LTC3535 has left Burst Mode op-
eration and returned to normal operation, it will remain
there until the output load is reduced below the burst
threshold current.
Burst Mode operation is inhibited during start-up and
soft-start and until V OUT is at least 0.24V greater than V IN .
Note that each channel can enter or leave Burst Mode
operation independent of the other channel.
PCB LAYOUT GUIDELINES
The high speed operation of the LTC3535 demands careful
attention to board layout. A careless layout will result in
reduced performance. Figure 2 shows the recommended
component placement. A large ground pin copper area
will help to lower the die temperature. A multilayer board
with a separate ground plane is ideal, but not absolutely
necessary.
The LTC3535 output disconnect feature allows output
short circuit while maintaining a maximum internally set
current limit. To reduce power dissipation under short-
circuit conditions, the peak switch current limit is reduced
to 400mA (typical per channel).
V OUT1
GND
SHDN
V IN1
GND
SCHOTTKY DIODE
Although not recommended, adding a Schottky diode from
SW to V OUT will improve efficiency by about 2%. Note
that this defeats the output disconnect and short-circuit
protection features.
V OUT2 V IN2
SHDN
Figure 2. Recommended Component Placement
3535fa
11
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3536IMSE#TRPBF | IC REG BUCK BST SYNC ADJ 12MSOP |
| LTC3538EDCB#TRPBF | IC REG BUCK BOOST SYNC ADJ 8DFN |
| LTC3539EDCB-2#TRPBF | IC REG BOOST SYNC ADJ 2A 8DFN |
| LTC3542IDC#TRMPBF | IC REG BUCK SYNC ADJ 0.5A 6DFN |
| LTC3543EDCB#TRPBF | IC REG BUCK SYNC ADJ 0.6A 8DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3535EDD-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Channel 550mA 1MHz Synchronous Step-Up DC/DC Converter |
| LTC3536EDD#PBF | 功能描述:IC REG BUCK BOOST SYNC ADJ 12DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3536EDD#TRPBF | 功能描述:IC REG BUCK BOOST SYNC ADJ 12DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3536EMSE#PBF | 功能描述:IC REG BUCK BST SYNC ADJ 12MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3536EMSE#TRPBF | 功能描述:IC REG BUCK BST SYNC ADJ 12MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。