- 您现在的位置：买卖IC网 > PDF目录80264 > LTC3536IDD#TRPBF (LINEAR TECHNOLOGY CORP) 4 A SWITCHING REGULATOR, 1440 kHz SWITCHING FREQ-MAX, PDSO10 PDF资料下载
参数资料
| 型号： | LTC3536IDD#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 4 A SWITCHING REGULATOR, 1440 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封装： | 3 X 3 MM, LEAD FREE, PLASTIC, MO-229WEED-2, DFN-10 |
| 文件页数： | 3/28页 |
| 文件大小： | 1088K |
| 代理商： | LTC3536IDD#TRPBF |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC3536
11
3536f
OPERATION
Reverse Current Limit
In PWM mode operation the LTC3536 has the ability to
actively conduct current away from the output if that is
necessarytomaintainregulation.Iftheoutputisheldabove
regulation, this could result in large reverse currents. This
situation can occur if the output of the LTC3536 is held
up momentarily by another supply as may occur during a
power-up or power-down sequence. To prevent damage to
the part under such conditions, the LTC3536 has a reverse
current comparator that monitors the current entering
powerswitchDfromtheload.Ifthiscurrentexceeds0.55A
(typical) switch D is turned off for the remainder of the
switching cycle in order to prevent the reverse inductor
current from reaching unsafe levels.
For no-load current application, the inductor current ripple
must be lower than double the minimum reverse current
limit (0.3A 2 = 0.6A maximum inductor current ripple).
See the Inductor Selection section for information about
how to calculate the inductor current ripple.
Output Current Capability
The maximum output current that can be delivered by
the LTC3536 is dependent upon many factors, the most
significant being the input and output voltages. For VOUT
= 3.3V and VIN ≥ 3V, the LTC3536 is able to support a 1A
load continuously. For VOUT = 3.3V and VIN =1.8V, the
LTC3536 is able to support a 300mA load continuously.
Typically, the output current capability is greatest when
the input voltage is approximately equal to the output
voltage. At larger step-up voltage ratios, the output cur-
rent capability is reduced because the lower duty cycle of
switch D results in a larger inductor current being needed
to support a given load. Additionally, the output current
capability generally decreases at large step-down voltage
ratios due to higher inductor current ripple which reduces
the maximum attainable inductor current.
Theoutputcurrentcapabilitycanalsobeaffectedbyinduc-
tor characteristics. An inductor with large DC resistance
will degrade output current capability, particularly in boost
mode operation. In addition, larger value inductors gener-
allymaximizeoutputcurrentcapabilitybyreducinginductor
currentripple.SeetheTypicalPerformanceCharacteristics
and the Inductor Selection section for information.
Burst Mode OPERATION
When MODE/SYNC is held high, the buck-boost converter
operatesinBurstModeoperationusingavariablefrequency
switching algorithm that minimizes the no-load input
quiescent current and improves efficiency at light load by
reducing the amount of switching to the minimum level
required to support the load. The output current capabil-
ity in Burst Mode operation is substantially lower than in
PWMmodeandisintendedtosupportlightstand-byloads.
Curves showing the maximum Burst Mode load current
as a function of the input and output voltage can be found
in the Typical Performance Characteristics section of this
data sheet. If the converter load in Burst Mode operation
exceeds the maximum Burst Mode current capability, the
output will lose regulation.
Each Burst Mode cycle is initiated when switches A and
C turn on producing a linearly increasing current through
the inductor. When the inductor current reaches the Burst
Mode peak current limit (0.6A typically), switches B and D
are turned on, discharging the energy stored in the induc-
tor into the output capacitor and load. Once the inductor
current reaches zero, all switches are turned off and the
cycleiscomplete.Currentpulsesgeneratedinthismanner
are repeated as often as necessary to maintain regulation
of the output voltage. In Burst Mode operation, the error
amplifier is used as burst comparator. If the MODE pin
is driven externally to a level higher than VIN, a current
limiting resistor should be used. 1M for 6V on the MODE
pin limits the current to 6A. Also, a Schottky diode from
the MODE pin to VIN can be used in addition to current
limiting resistor.
SOFT-START
To minimize input current transients on power-up, the
LTC3536 incorporates an internal soft-start circuit with a
nominal duration of 0.9ms. The soft-start is implemented
by a linearly increasing ramp of the error amplifier refer-
ence voltage during the soft-start duration. As a result,
the duration of the soft-start period is largely unaffected
by the size of the output capacitor or the output regula-
tion voltage. Given the closed-loop nature of the soft-start
implementation, the converter is able to respond to load
transients that occur during the soft-start interval. The
相关PDF资料 |
PDF描述 |
|---|---|
| LM4576-3.3BT | 3.5 A SWITCHING REGULATOR, 200 kHz SWITCHING FREQ-MAX, PSFM5 |
| LS1501-7ERD6TB1 | 1-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
| LC5523FLF3052 | POWER FACTOR CONTROLLER, 18 kHz SWITCHING FREQ-MAX, ZFM7 |
| LK1001-7D7 | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LK1001-7DDT | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3536IMSE#PBF | 功能描述:IC REG BUCK BST SYNC ADJ 12MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3536IMSE#TRPBF | 功能描述:IC REG BUCK BST SYNC ADJ 12MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3537 | 制造商:LINER 制造商全称:Linear Technology 功能描述:2.2 MHz, 600mA Synchronous Step-Up DC/DC Converter and 100mA LDO |
| LTC3537EUD#PBF | 功能描述:IC REG DL BST/LINEAR SYNC 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| LTC3537EUD#TRPBF | 功能描述:IC REG DL BST/LINEAR SYNC 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
发布紧急采购，3分钟左右您将得到回复。