- 您现在的位置：买卖IC网 > Datasheet目录41 > LTC3541EDD#TRPBF (Linear Technology)IC REG DL BCK/LINEAR SYNC 10-DFN Datasheet资料下载
参数资料
| 型号： | LTC3541EDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 12/20页 |
| 文件大小： | 368K |
| 描述： | IC REG DL BCK/LINEAR SYNC 10-DFN |
| 产品培训模块： | More Information on LDOs |
| 标准包装： | 2,500 |
| 拓扑： | 降压（降压）同步（1），线性（LDO）（1） |
| 功能： | 任何功能 |
| 输出数： | 2 |
| 频率 - 开关： | 2.25MHz |
| 电压/电流 - 输出 1： | 0.8 V ~ 5 V，500mA |
| 电压/电流 - 输出 2： | 0.4 V ~ 4.1 V，300mA |
| 带 LED 驱动器： | 无 |
| 带监控器： | 无 |
| 带序列发生器： | 是 |
| 电源电压： | 0.9 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-DFN（3x3） |
| 包装： | 带卷 (TR) |
LTC3541
3541fa
PPLICATIO S I FOR ATIO
U
U
be obtained by choosing an output capacitor value of 10礔
to 22礔. Typically, once the ESR requirement for C
OUT
has
been met, the RMS current rating generally far exceeds
the I
RIPPLE(P-P)
requirement. The output ripple 擵
OUT
is
determined by:
E?nbsp +
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
V I ESR
fc
OUT L
OUT
1
8
where f = operating frequency, C
OUT
= output capacitance
and 擨
L
= ripple current in the inductor. For a fixed output
voltage, the output ripple is highest at maximum input
voltage since 擨
L
increases with input voltage.
Aluminum electrolytic and dry tantalum capacitors are both
available in surface mount configurations. In the case of
tantalum, it is critical that the capacitors are surge tested
for use in switching power supplies. An excellent choice is
the AVX TPS series of surface mount tantalum. These are
specially constructed and tested for low ESR so they give
the lowest ESR for a given volume. Other capacitor types
include Sanyo POSCAP, Kemet T510 and T495 series, and
Sprague 593D and 595D series. Consult the manufacturer
for other specific recommendations.
Using Ceramic Input and Output Capacitors
High value, low cost ceramic capacitors are now becoming
available in smaller case sizes. Their high ripple current,
high voltage rating, and low ESR make them ideal for
switching regulator applications. Since the LTC3541s
control loop does not depend on the output capacitors
ESR for stable operation, ceramic capacitors can be used
freely to achieve very low output ripple and small circuit
size.
However, care must be taken when ceramic capacitors
are used at the input and the output. When a ceramic
capacitor is used at the input and the power is supplied
by a wall adapter through long wires, a load step at the
output can induce ringing at the input, V
IN
. At best, this
ringing can couple to the output and be mistaken as loop
instability. At worst, a sudden inrush of current through
the long wires can potentially cause a voltage spike at V
IN
,
large enough to damage the part.
When choosing the input and output ceramic capacitors,
choose the X5R or X7R dielectric formulations. These
dielectrics have the best temperature and voltage charac-
teristics of all the ceramics for a given value and size.
Output Voltage Programming
The output voltage is set by tying BUCKFB to a resistive
divider according to the following formula:
V
R
R
OUT
= +
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
08 1
2
1
.
Since the impedance at the BUCKFB pin is dependant upon
the resistor divider network used, and phase shift due to
this impedance directly impacts the transient response of
the buck, R1 should be chosen <125k. In addition, stray
capacitance at this pin should be minimized (<5pF) to pre-
vent excessive phase shift. Finally, special attention should
be given to any stray capacitances that can couple external
signals onto the BUCKFB pin producing undesirable output
ripple. For optimum performance connect the BUCKFB
pin to R1 and R2 with a short PCB trace and minimize all
other stray capacitance to the BUCKFB pin.
The external resistive divider is connected to the output,
allowing remote voltage sensing as shown in Figure 6.
Checking Transient Response
The regulator loop response can be checked by looking
at the load transient response. Switching regulators take
several cycles to respond to a step in load current. When
a load step occurs, V
OUT
immediately shifts by an amount
equal to (擨
LOAD
" ESR), where ESR is the effective series
Figure 6. Setting the LTC3541 Output Voltage
BUcKFB
GND
LTc3541
0.8V d V
OUT
d 5V
R2
R1
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3670EDDB#TRPBF | IC REG TRPL BCK/LINEAR 12DFN |
| LTC3672BEDC-1#TRPBF | IC REG TRPL BCK/LINEAR 8-DFN |
| LTC3700EMS#TRPBF | IC REG DL BUCK/LINEAR 10MSOP |
| LTC4151HMS#TRPBF | IC PWR MONITOR MS 80V SD 10MSOP |
| LTC4210-2CS6#TRM | IC CONTROLLER HOT SWAP TSOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3542 | 制造商:LINER 制造商全称:Linear Technology 功能描述:500mA, 2.25MHz Synchronous Step-Down DC/DC Converter |
| LTC3542-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:500mA, 2.25MHz 2.8V Output Synchronous Step-Down DC/DC Converter |
| LTC3542EDC#PBF | 制造商:Linear Technology 功能描述:DC-DC CONVERTER BUCK 2.25MHZ 制造商:Linear Technology 功能描述:DC-DC CONVERTER, BUCK, 2.25MHZ, 500mA, DFN-6; Primary Input Voltage:5.5V; No. of Outputs:1; Output Current:500mA; No. of Pins:6; Operating Temperature Min:-40C; Operating Temperature Max:85C; Package / Case:6-DFN ;RoHS Compliant: Yes |
| LTC3542EDC#TRMPBF | 功能描述:IC REG BUCK SYNC ADJ 0.5A 6DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:High Efficiency Current Mode Switching Regulators CMOS LDO Regulators 特色产品:BD91x Series Step-Down Regulators 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:两者兼有 输出数:2 输出电压:3.3V，0.8 V ~ 2.5 V 输入电压:4.5 V ~ 5.5 V PWM 型:电流模式 频率 - 开关:1MHz 电流 - 输出:1.5A 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 包装:带卷 (TR) 供应商设备封装:VQFN020V4040 产品目录页面:1373 (CN2011-ZH PDF) 其它名称:BD9152MUV-E2TR |
| LTC3542EDC#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 0.5A 6DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:500 系列:- 类型:切换式电容器（充电泵），反相 输出类型:固定 输出数:1 输出电压:-3V 输入电压:2.3 V ~ 5.5 V PWM 型:Burst Mode? 频率 - 开关:900kHz 电流 - 输出:100mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 细型，TSOT-23-6 包装:带卷 (TR) 供应商设备封装:TSOT-23-6 其它名称:LTC1983ES6-3#TRMTR |
发布紧急采购，3分钟左右您将得到回复。