- 您现在的位置：买卖IC网 > PDF目录30770 > LTC3546EUFD (LINEAR TECHNOLOGY CORP) DUAL SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PQCC28 PDF资料下载
参数资料
| 型号： | LTC3546EUFD |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | DUAL SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PQCC28 |
| 封装： | 4 X 5 MM, PLASTIC, MO-220, QFN-28 |
| 文件页数： | 16/28页 |
| 文件大小： | 356K |
| 代理商： | LTC3546EUFD |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC3546
23
3546fb
APPLICATIONS INFORMATION
operating frequency of 1.5MHz and assumes roughly a
300mA/A load step.
C
F
A
mA
A
F
C
OUT
OU
1
22
08
280
300
08
20 5
==
.
.
T
F
A
mA
A
F
1
22
25
875
300
25
64 2
==
.
.
The closest values are 22μF and 68μF.
The output voltages can now be programmed by choos-
ing the values of R1, R2, R3, and R4. To maintain high
efciency, the current in these resistors should be kept
small. Choosing 2μA with the 0.6V feedback voltages
makes R2 and R4 equal to 300k. A close standard 1%
resistor is 301k. This then makes R1 = 300k. A close
standard 1% is 301k. R3 then equals 600k. A close 1%
resistor is 604k.
The compensation should be optimized for these com-
ponents by examining the load step response but a good
place to start for the LTC3546 is with a 13kΩ and 1000pF
lter on both ITH1 and ITH2. The output capacitor may
need to be increased depending on the actual transient
during a load step.
The PGOOD pin is a common drain output and requires a
pull-up resistor. A 100k resistor is used for adequate speed.
Figure 9 shows a complete schematic for this design.
Board Layout Considerations
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of
the LTC3546. These items are also illustrated graphically
in the layout diagram of Figure 7. Check the following in
your layout.
1. Make sure SW1, SW2A, SW2B and SW1D are connected
on the PC board through a wide piece of copper.
2. All, or part, of CIN should connect from Pin 9 to Pin 14
on the same side of the PC board as the chip and as
close to the chip as possible, where the SW traces will go
directly under the capacitor. CIN provides the AC current
to the internal power MOSFETs and their drivers.
3. Are the respective COUT, L closely connected? The (–)
plate of COUT1 returns current to PGND1, and the (–)
plate of COUT2 returns current to the PGND2. The (–)
plate of CIN should also return current to PGND1 and
PGND2.
4. The resistor divider, R1 and R2, must be connected
between the (+) plate of COUT1 and a ground line ter-
minated near GNDA. The resistor divider R3 and R4,
must be connected between the (+) plate of COUT2 and
the ground connection terminated to the GNDA pin.
The feedback signals VFB1 and VFB2 should be routed
away from noise components and traces, such as the
SW lines, and its trace should be minimized.
5. When using the RFREQ resistor, the ground connection
of the resistor should be terminated to the GNDA pin.
When using the internal PLL, the ground connection of
the R-C compensation network should be terminated
to the GNDA pin.
6. Keep sensitive components away from the SW pins.
The input capacitor CIN, the compensation capacitors
CFF1, CFF2, CITH1, and CITH2 and all resistors R1, R2,
R3, R4, RITH1 and RITH2 should be routed away from
the SW traces and the inductors L1 and L2.
7. A ground plane is preferred, but if not available, keep
the signal and power grounds segregated with small
signal components returning to the SGND pin at one
point which is then connected to the PGND1/PGND2/
PGND1D/GNDD pins.
8. Flood all unused areas on all layers with copper. Flooding
with copper will reduce the temperature rise of power
components. These copper areas should be connected
to the Exposed Pad (Pin 29).
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3546IUFD#TR | DUAL SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PQCC28 |
| LTC3546EFE | DUAL SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PDSO28 |
| LTC3546IFE#TRPBF | DUAL SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PDSO28 |
| LTC3546IFE#TR | DUAL SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PDSO28 |
| LTC3554EUD-2#TRPBF | 0.6 A BATTERY CHARGE CONTROLLER, 2590 kHz SWITCHING FREQ-MAX, PQCC20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3546EUFD#PBF | 功能描述:IC REG BUCK SYNC ADJ 1A/2A 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:MIC23xxx HyperLight Load™ Regulators 标准包装:5,000 系列:HyperLight Load® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.8V 输入电压:2.7 V ~ 5.5 V PWM 型:混合物 频率 - 开关:4MHz 电流 - 输出:2A 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 包装:带卷 (TR) 供应商设备封装:8-MLF?（2x2） 产品目录页面:1094 (CN2011-ZH PDF) 其它名称:576-3303-2 |
| LTC3546EUFD#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 1A/2A 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3546EUFDPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Synchronous, 3A/1A or 2A/2A Confi gurable Step-Down DC/DC Regulator |
| LTC3546EUFDTRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Synchronous, 3A/1A or 2A/2A Confi gurable Step-Down DC/DC Regulator |
| LTC3546IFE#PBF | 功能描述:IC REG BUCK SYNC ADJ DL 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。