- 您现在的位置：买卖IC网 > PDF目录79812 > LTC3554EPD#TRPBF (LINEAR TECHNOLOGY CORP) 0.6 A BATTERY CHARGE CONTROLLER, 2590 kHz SWITCHING FREQ-MAX, PQCC20 PDF资料下载
参数资料
| 型号： | LTC3554EPD#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 0.6 A BATTERY CHARGE CONTROLLER, 2590 kHz SWITCHING FREQ-MAX, PQCC20 |
| 封装： | 3 X 3 MM, LEAD FREE, PLASTIC, UTQFN-20 |
| 文件页数： | 9/36页 |
| 文件大小： | 418K |
| 代理商： | LTC3554EPD#TRPBF |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LTC3554/LTC3554-2
17
35542fb
Battery Charger Stability Considerations
The LTC3554’s battery charger contains both a constant-
voltage and a constant-current control loop. The constant-
voltage loop is stable without any compensation when a
battery is connected with low impedance leads. Excessive
lead length, however, may add enough series inductance
to require a bypass capacitor of at least 1μF from BAT to
GND. Furthermore, a 100μF 1210 ceramic capacitor in
series with a 0.3Ω resistor from BAT to GND is required
to keep ripple voltage low if operation with the battery
disconnected is allowed.
High value, low ESR multilayer ceramic chip capacitors
reduce the constant-voltage loop phase margin, possibly
resulting in instability. Ceramic capacitors up to 22μF may
be used in parallel with a battery, but larger ceramics should
be decoupled with 0.2Ω to 1Ω of series resistance.
In constant-current mode, the PROG pin is in the feed-
back loop rather than the battery voltage. Because of the
additional pole created by any PROG pin capacitance,
capacitance on this pin must be kept to a minimum. With
no additional capacitance on the PROG pin, the battery
charger is stable with program resistor values as high
as 25k. However, additional capacitance on this node
reduces the maximum allowed program resistor. The pole
frequency at the PROG pin should be kept above 100kHz.
Therefore, if the PROG pin has a parasitic capacitance,
CPROG, the following equation should be used to calculate
the maximum resistance value for RPROG:
R
PROG ≤
1
2
π 100kHz C
PROG
NTC Thermistor
The battery temperature is measured by placing a nega-
tive temperature coefcient (NTC) thermistor close to the
battery pack. To use this feature connect the NTC therm-
istor, RNTC, between the NTC pin and ground and a bias
resistor, RNOM, from VBUS to NTC, as shown in Figure 1.
RNOM should be a 1% resistor with a value equal to the
value of the chosen NTC thermistor at 25°C (R25). The
LTC3554 will pause charging when the resistance of the
NTC thermistor drops to 0.54 times the value of R25
or approximately 54k (for a Vishay curve 1 thermistor,
this corresponds to approximately 40°C). If the battery
charger is in constant-voltage mode, the safety timer also
pauses until the thermistor indicates a return to a valid
temperature. As the temperature drops, the resistance of
the NTC thermistor rises. The LTC3554 is also designed
to pause charging when the value of the NTC thermistor
increases to 3.17 times the value of R25. For a Vishay
curve 1 thermistor this resistance, 317k, corresponds to
approximately 0°C. The hot and cold comparators each
have approximately 3°C of hysteresis to prevent oscillation
about the trip point.
Alternate NTC Thermistors and Biasing
The LTC3554 provides temperature qualied charging if
a grounded thermistor and a bias resistor are connected
to NTC. By using a bias resistor whose value is equal to
the room temperature resistance of the thermistor (R25)
the upper and lower temperatures are preprogrammed
to approximately 40°C and 0°C, respectively (assuming
a Vishay curve 1 thermistor).
The upper and lower temperature thresholds can be
adjusted by either a modication of the bias resistor value
or by adding a second adjustment resistor to the circuit.
If only the bias resistor is adjusted, then either the upper
or the lower threshold can be modied but not both. The
other trip point will be determined by the characteristics
of the thermistor. Using the bias resistor in addition to an
adjustment resistor, both the upper and the lower tem-
perature trip points can be independently programmed
with the constraint that the difference between the upper
and lower temperature thresholds cannot decrease.
Examples of each technique are given below.
OPERATION
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3865IUH-1#PBF | DUAL SWITCHING CONTROLLER, 880 kHz SWITCHING FREQ-MAX, PQCC32 |
| LS5660-9PDDT | 2-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
| LS2660-7ERD1TB1 | 2-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
| LX6431BIPKT | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, PSSO3 |
| LK1001-7ERD1T | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3554EUD#PBF | 功能描述:IC USB POWER MANAGER 20UTQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:热电冷却器 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.173"，4.40mm 宽）裸露焊盘 供应商设备封装:28-TSSOP 裸露焊盘 包装:管件 产品目录页面:1410 (CN2011-ZH PDF) |
| LTC3554EUD#TRPBF | 功能描述:IC USB POWER MANAGER 20UTQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:PowerPath™ 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| LTC3554EUD-1#PBF | 功能描述:IC USB POWER MANAGER 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:PowerPath™ 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| LTC3554EUD-1#TRPBF | 功能描述:IC USB POWER MANAGER 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:PowerPath™ 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| LTC3554EUD-2#PBF | 功能描述:IC USB POWER MANAGER 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:热电冷却器 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.173"，4.40mm 宽）裸露焊盘 供应商设备封装:28-TSSOP 裸露焊盘 包装:管件 产品目录页面:1410 (CN2011-ZH PDF) |
发布紧急采购，3分钟左右您将得到回复。