- 您现在的位置：买卖IC网 > PDF目录98003 > LTC3559EUD (LINEAR TECHNOLOGY CORP) 1.05 A BATTERY CHARGE CONTROLLER, 2590 kHz SWITCHING FREQ-MAX, PQCC16 PDF资料下载
参数资料
| 型号： | LTC3559EUD |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 1.05 A BATTERY CHARGE CONTROLLER, 2590 kHz SWITCHING FREQ-MAX, PQCC16 |
| 封装： | 3 X 3 MM, PLASTIC, MO-220WEED-2, QFN-16 |
| 文件页数： | 24/24页 |
| 文件大小： | 302K |
| 代理商： | LTC3559EUD |
LTC3559
9
3559f
GND (Pin1): Ground, Connect to Exposed Pad (Pin 17).
BAT (Pin 2): Charge Current Output. Provides charge cur-
rent to the battery and regulates nal oat voltage to 4.2V.
MODE (Pin 3): MODE Pin for Buck Regulators. When held
high, both regulators are in Burst Mode operation. When
held low both regulators operate in pulse skip mode. This
pin is a high impedance input; do not oat.
FB1 (Pin 4): Buck 1 Feedback Voltage Pin. Receives feed-
back by a resistor divider connected across the output.
EN1 (Pin 5): Enable Input Pin for Buck 1. This pin is a high
impedance input; do not oat. Active high.
SW1 (Pin 6): Buck 1 Switching Node. External inductor
connects to this node.
PVIN (Pin 7): Input Supply Pin for Buck Regulators.
Connect to BAT. A 2.2
μF decoupling capacitor to GND is
recommended.
SW2 (Pin 8): Buck 2 Switching Node. External inductor
connects to this node.
EN2 (Pin 9): Enable Input Pin for Buck 2. This pin is a high
impedance input; do not oat. Active high.
FB2 (Pin 10): Buck 2 Feedback Voltage Pin. Receives feed-
back by a resistor divider connected across the output.
SUSP (Pin 11): Suspend Battery Charging Operation.
A voltage greater than 1.2V on this pin puts the battery
charger into suspend mode, disables the charger and
resets the termination timer. A weak pull-down current is
internally applied to this pin to ensure it is low at power
up when the input is not being driven externally.
HPWR (Pin 12): High Current Battery Charging Enabled.
A voltage greater than 1.2V at this pin programs the
BAT pin current at 100% of the maximum programmed
charge current. A voltage less than 0.4V sets the BAT pin
current to 20% of the maximum programmed charge
current. When used with a 1.74k PROG resistor, this pin
can toggle between low power and high power modes per
USB specication. A weak pull-down current is internally
applied to this pin to ensure it is low at power up when
the input is not being driven externally.
NTC (Pin 13): Input to the NTC Thermistor Monitoring
Circuit. The NTC pin connects to a negative temperature
coefcient thermistor which is typically co-packaged with
the battery pack to determine if the battery is too hot or
too cold to charge. If the battery temperature is out of
range, charging is paused until the battery temperature
re-enters the valid range. A low drift bias resistor is re-
quired from VCC to NTC and a thermistor is required from
NTC to ground. To disable the NTC function, the NTC pin
should be grounded.
PROG (Pin 14): Charge Current Program and Charge
Current Monitor Pin. Charge current is programmed by
connecting a resistor from PROG to ground. When charging
in constant current mode, the PROG pin servos to 1V if
the HPWR pin is pulled high, or 200mV if the HPWR pin
is pulled low. The voltage on this pin always represents
the battery current through the following formula:
I
PROG
R
BAT
PROG
=
800
CHRG (Pin 15): Open-Drain Charge Status Output. The
CHRG pin indicates the status of the battery charger. Four
possible states are represented by
CHRG: charging, not
charging (i.e., the charge current is less than 1/10th of the
full-scale charge current), unresponsive battery (i.e., the
battery voltage remains below 2.9V after 1/2 hour of charg-
ing) and battery temperature out of range.
CHRG requires
a pull-up resistor and/or LED to provide indication.
VCC (Pin 16): Battery Charger Input. A 1μF decoupling
capacitor to GND is recommended.
Exposed Pad (Pin 17): Ground. The Exposed Pad must
be soldered to PCB ground to provide electrical contact
and rated thermal performance.
PIN FUNCTIONS
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3586EUFE#PBF | 3 A BATTERY CHARGE CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PQCC38 |
| LTC3586EUFE-1#PBF | BATTERY CHARGE CONTROLLER, PQCC38 |
| LTC3586EUFE-1#TRPBF | BATTERY CHARGE CONTROLLER, PQCC38 |
| LTC3672BEDC-1#PBF | 1.1 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO8 |
| LTC3728LZEUH | 3 A DUAL SWITCHING CONTROLLER, 590 kHz SWITCHING FREQ-MAX, PQCC28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3559EUD#PBF | 功能描述:IC USB CHARGER 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC3559EUD#PBF | 制造商:Linear Technology 功能描述:IC BATT CHARGER W/BUCK REG 16QFN 制造商:Linear Technology 功能描述:IC, BATT CHARGER, W/BUCK REG, 16QFN |
| LTC3559EUD#TRPBF | 功能描述:IC USB CHARGER 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC3559EUD-1#PBF | 功能描述:IC USB BATTERY CHARGER 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC3559EUD-1#TRPBF | 功能描述:IC USB BATTERY CHARGER 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。