- 您现在的位置：买卖IC网 > PDF目录14028 > LTC3600EDD#PBF (Linear Technology)IC REG BUCK SYNC ADJ 1.5A 12DFN PDF资料下载
参数资料
| 型号： | LTC3600EDD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/28页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 1.5A 12DFN |
| 标准包装： | 121 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0 V ~ 14.5 V |
| 输入电压： | 4 V ~ 15 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1MHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-WFDFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 12-DFN（3x3） |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC3600
PIN FUNCTIONS
ISET (Pin 1): Accurate 50μA Current Source. Positive input
to the error amplifier. Connect an external resistor from this
pin to signal GND to program the V OUT voltage. Connecting
an external capacitor from ISET to ground will soft start
the output voltage and reduce current inrush when turning
on. V OUT can also be programmed by driving ISET directly
with an external supply from 0 to V IN , in which case the
external supply would be sinking the provided 50μA. Do
not drive V ISET above V IN or below GND. Do not float ISET.
ITH (Pin 2): Error Amplifier Output and Switching
Regulator Compensation Point. The internal current
comparator’s trip threshold is linearly proportional to
this voltage, whose normal range is from 0.3V to 2.4V.
For external compensation, tie a resistor (R ITH ) in series
with a capacitor (C ITH ) to signal GND. A separate 10pF
high frequency filtering capacitor can also be placed
from ITH to signal GND. Tying ITH to INTV CC activates
internal compensation.
RT (Pin 3): Switching Frequency Programming Pin. Con-
nect an external resistor (between 200k to 10k) from RT
to SGND to program the frequency from 200kHz to 4MHz.
Tying the RT pin to INTV CC programs 1MHz operation.
Do not float the RT pin.
PGFB (Pin 4): Power Good Feedback. Place a resistor
divider on V OUT to detect power good level. If PGFB is
more than 0.645V, or less than 0.555V, PGOOD will be
pulled down. Tie PGFB to INTV CC to disable the PGOOD
function. Tying PGFB to a voltage greater than 0.64V and
less than 4V will force continuous synchronous operation
regardless of the MODE/SYNC state.
RUN (Pin 5): Run Control Input. Enables chip operation by
tying RUN above 1.55V. Tying it below 1V shuts down the
switching regulator. Tying it below 0.4V shuts off the entire
chip. When tying RUN to more than 12V, place a resistor
(100k to 500k) between RUN and the voltage source.
MODE/SYNC (Pin 6): Operation Mode Select. Tie this pin
to INTV CC to force continuous synchronous operation at
all output loads. Tying it to GND enables discontinuous
mode operation at light loads. Applying an external clock
signal to this pin will synchronize switching frequency
to the external clock. During external clock synchroniza-
tion, R T value should be set up such that the free running
frequency is within 30% of the external clock frequency.
SW (Pin 7): Switch Node Connection to External Inductor.
Voltage swing of SW is from a diode voltage drop below
ground to V IN .
V IN (Pin 8): Input voltage. Must decouple to GND with a
capacitor close to the V IN pin.
BOOST (Pin 9): Boosted Floating Driver Supply for Inter-
nal Top Power MOSFET. The (+) terminal of the bootstrap
capacitor connects here. This pin swings from a diode
voltage drop below INTV CC up to V IN + INTV CC .
INTV CC (Pin 10): Internal 5V Regulator Output. The internal
power drivers and control circuits are powered from this
voltage. Decouple this pin to GND with a minimum of 1μF
low ESR ceramic capacitor.
V OUT (Pin 11): Output Voltage Pin. Output of the LTC3600
voltage regulator. Also the negative input of the error
amplifier which is driven to be the same voltage as ISET.
PGOOD (Pin 12): Output Power Good with Open-Drain
Logic. PGOOD is pulled to ground when the PGFB pin is
more than 0.645V or less than 0.555V. PGOOD open-drain
logic will be disabled if PGFB is tied to INTV CC .
GND (Exposed Pad Pin 13): Ground. Return path of internal
power MOSFETs. Connect the exposed pad to the negative
terminal of the input capacitor and output capacitor.
3600fc
8
相关PDF资料 |
PDF描述 |
|---|---|
| EBC60DCMD-S288 | CONN EDGECARD 120POS .100 EXTEND |
| HM79S-125391LFTR13 | SHIELDED DRUM INDUCTORS |
| LT3574EMS#TRPBF | IC REG FLYBK ISO ADJ .65A 16MSOP |
| TFL0816-18N | INDUCTOR 18NH +/-2% 0603 |
| HM79S-125331LFTR13 | SHIELDED DRUM INDUCTORS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3600EMSE#PBF | 功能描述:IC REG BUCK SYNC ADJ 1.5A 12MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3600EMSE#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 1.5A 12MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3600IDD#PBF | 功能描述:IC REG BUCK SYNC ADJ 1.5A 12DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3600IDD#PBF | 制造商:Linear Technology 功能描述:IC SYNC BUCK DC-DC CONV 4 MHz DFN-12 |
| LTC3600IDD#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 1.5A 12DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。