- 您现在的位置：买卖IC网 > PDF目录14798 > LTC3602EUF#PBF (Linear Technology)IC REG BUCK SYNC ADJ 2.5A 20QFN PDF资料下载
参数资料
| 型号： | LTC3602EUF#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 2.5A 20QFN |
| 标准包装： | 91 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 9.5 V |
| 输入电压： | 4.5 V ~ 10 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 1MHz |
| 电流 - 输出： | 2.5A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 20-QFN 裸露焊盘（4x4） |
| 产品目录页面： | 1335 (CN2011-ZH PDF) |
LTC3602
APPLICATIONS INFORMATION
characteristics. The choice of which style inductor to use
mainly depends on the price vs size requirements and any
radiated ?eld/EMI requirements. New designs for surface
mount inductors are available from Coiltronics, Coilcraft,
Toko and Sumida.
C IN and C OUT Selection
The input capacitance, C IN , is needed to ?lter the trapezoi-
dal current at the source of the top MOSFET. To prevent
large ripple voltage, a low ESR input capacitor sized for
the maximum RMS current should be used. RMS current
is given by:
density than other types. Tantalum capacitors have the
highest capacitance density but it is important to only
use types that have been surge tested for use in switching
power supplies. Aluminum electrolytic capacitors have
signi?cantly higher ESR but can be used in cost-sensitive
applications provided that consideration is given to ripple
current ratings and long term reliability. Ceramic capacitors
have excellent low ESR characteristics but can have a high
voltage coef?cient and audible piezoelectric effects. The
high Q of ceramic capacitors with trace inductance can
also lead to signi?cant ringing.
Using Ceramic Input and Output Capacitors
I RMS = I OUT ( MAX ) ?
V OUT
V IN
?
V IN
V OUT
–1
Higher values, lower cost ceramic capacitors are now
becoming available in smaller case sizes. Their high ripple
current, high voltage rating and low ESR make them ideal
V OUT = 0.6V ? ? 1 +
This formula has a maximum at V IN = 2V OUT , where
I RMS = I OUT /2. This simple worst-case condition is com-
monly used for design because even signi?cant deviations
do not offer much relief. Note that ripple current ratings
from capacitor manufacturers are often based on only
2000 hours of life which makes it advisable to further
derate the capacitor, or choose a capacitor rated at a
higher temperature than required. Several capacitors may
also be paralleled to meet size or height requirements in
the design.
The selection of C OUT is determined by the effective series
resistance (ESR) that is required to minimize voltage ripple
and load step transients, as well as the amount of bulk
capacitance that is necessary to ensure that the control
loop is stable. Loop stability can be checked by viewing
the load transient response as described in a later section.
The output ripple, Δ V OUT , is determined by:
for switching regulator applications. However, care must
be taken when these capacitors are used at the input and
output. When a ceramic capacitor is used at the input and
the power is supplied by a wall adapter through long wires,
a load step at the output can induce ringing at the input,
V IN . At best, this ringing can couple to the output and be
mistaken as loop instability. At worst, a sudden inrush
of current through the long wires can potentially cause a
voltage spike at V IN large enough to damage the part.
Output Voltage Programming
The output voltage is set by an external resistive divider
according to the following equation:
? R2 ?
?
? R1 ?
The resistive divider allows the V FB pin to sense a fraction
Δ V OUT ≤ Δ I L ? ? ESR +
?
?
1 ?
8 fC OUT ? ?
of the output voltage as shown in Figure 1.
V OUT
The output ripple is highest at maximum input voltage
since Δ I L increases with input voltage. Multiple capacitors
placed in parallel may be needed to meet the ESR and
RMS current handling requirements. Dry tantalum, special
polymer, aluminum electrolytic and ceramic capacitors are
all available in surface mount packages. Special polymer
V FB
LTC3602
SGND
3602 F01
R2
R1
capacitors offer very low ESR but have lower capacitance
Figure 1. Setting the Output Voltage
3602fb
10
相关PDF资料 |
PDF描述 |
|---|---|
| EB43-S1R1560W-7 | CONN EDGEBOARD DUAL 30POS 3A |
| LT3693EDD#PBF | IC REG BUCK ADJ 3.5A 10DFN |
| RBC25DCAN | CONN EDGECARD 50POS R/A .100 SLD |
| LT3680EMSE#PBF | IC REG BUCK ADJ 3.5A 10MSOP |
| RBC25DCAH | CONN EDGECARD 50POS R/A .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3602IFE#PBF | 功能描述:IC REG BUCK SYNC ADJ 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3602IFE#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3602IUF#PBF | 功能描述:IC REG BUCK SYNC ADJ 2.5A 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3602IUF#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 2.5A 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3603EMSE#PBF | 功能描述:IC REG BUCK SYNC ADJ 2.5A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
发布紧急采购，3分钟左右您将得到回复。