参数资料
型号: LTC3604EMSE#PBF
厂商: Linear Technology
文件页数: 9/24页
文件大小: 0K
描述: IC REG BUCK SYNC 2.5A 16MSOP
标准包装: 37
类型: 降压(降压)
输出数: 1
输入电压: 3.6 V ~ 15 V
PWM 型: 电流模式,混合
频率 - 开关: 800kHz ~ 4MHz
电流 - 输出: 2.5A
同步整流器:
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 16-TFSOP(0.118",3.00mm 宽)裸露焊盘
包装: 管件
供应商设备封装: 16-MSOP,裸露焊盘
产品目录页面: 1335 (CN2011-ZH PDF)
LTC3604
OPERATION
The LTC3604 is a current mode, monolithic, step-down
regulator capable of providing up to 2.5A of output current.
Its unique controlled on-time architecture allows extremely
low step-down ratios while maintaining a constant switch-
ing frequency. Part operation is enabled by raising the
voltage on the RUN pin above 1.25V nominally.
Main Control Loop
In normal operation the internal top power MOSFET is
turned on for a ?xed interval determined by an internal
one-shot timer (“ON” signal in the Block Diagram). When
the top power MOSFET turns off, the bottom power
MOSFET turns on until the current comparator, I CMP ,
trips, thus restarting the one-shot timer and initiating the
next cycle. The inductor current is monitored by sensing
the voltage drop across the SW and PGND nodes of the
bottom power MOSFET. The voltage at the ITH pin sets the
I CMP comparator threshold corresponding to the induc-
tor valley current. The error ampli?er EA adjusts this ITH
voltage by comparing an internal 0.6V reference to the
feedback signal, V FB , derived from the output voltage. If, for
example, the load current increases, the feedback voltage
will decrease relative to the internal 0.6V reference. The
ITH voltage then rises until the average inductor current
matches that of the load current.
The operating frequency is determined by the value of the
RT resistor, which programs the current for the internal
oscillator. An internal phase-locked loop servos the switch-
ing regulator on-time to track the internal oscillator edge
and force a constant switching frequency. A clock signal
can be applied to the MODE/SYNC pin to synchronize the
switching frequency to an external source. The regulator
defaults to forced continuous operation once the clock
signal is applied.
At low load currents the inductor current can drop to
zero or become negative. If the LTC3604 is con?gured for
Burst Mode operation, this inductor current condition is
detected by the current reversal comparator, I REV , which
the part into a low quiescent current sleep state resulting
in discontinuous operation and increased ef?ciency at low
load currents. Both power MOSFETs will remain off with
the part in sleep and the output capacitor supplying the
load current until the ITH voltage rises suf?ciently to initi-
ate another cycle. Discontinuous operation is disabled by
tying the MODE/SYNC pin to ground placing the LTC3604
into forced continuous mode. During forced continuous
mode, continuous synchronous operation occurs regard-
less of the output load current.
“Power Good” Status Output
The PGOOD open-drain output will be pulled low if the
regulator output exits a ±8% window around the regulation
point. This condition is released once regulation within a
±5% window is achieved. To prevent unwanted PGOOD
glitches during transients or dynamic V OUT changes, the
LTC3604 PGOOD falling edge includes a ?lter time of
approximately 40μs.
V IN Overvoltage Protection
In order to protect the internal power MOSFET devices
against transient voltage spikes, the LTC3604 constantly
monitors the V IN pin for an overvoltage condition. When
V IN rises above 17.5V, the regulator suspends operation
by shutting off both power MOSFETs. Once V IN drops
below 16.5V, the regulator immediately resumes normal
operation. The regulator does not execute its soft-start
function when exiting an overvoltage condition.
Short-Circuit Protection
Foldback current limiting is provided in the event the
output is inadvertently shorted to ground. During this
condition the internal current limit (I LIM ) will be lowered
to approximately one-third its normal value. This feature
reduces the heat dissipation in the LTC3604 during short-
circuit conditions and protects both the IC and the input
supply from any potential damage.
in turn shuts off the bottom power MOSFET and places
3604f
9
相关PDF资料
PDF描述
ECO-S1VA103EA CAP ALUM 10000UF 35V 20% SNAP
ESM24DRKH-S13 CONN EDGECARD 48POS .156 EXTEND
AMM06DSEI-S13 CONN EDGECARD 12POS .156 EXTEND
ACM15DSEF-S13 CONN EDGECARD EXTEND 30POS 0.156
EMM18DTKD CONN EDGECARD 36POS DIP .156 SLD
相关代理商/技术参数
参数描述
LTC3604EUD#PBF 功能描述:IC REG BUCK SYNC 2.5A 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压(降压) 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON(1.45x1) 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2
LTC3604EUD#PBF 制造商:Linear Technology 功能描述:IC, SYNC STEP-DOWN REGULATOR, QFN-16
LTC3604EUD#TRPBF 功能描述:IC REG BUCK SYNC 2.5A 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压(降压) 输出类型:固定 输出数:1 输出电压:1.2V,1.5V,1.8V,2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP,10-MSOP(0.118",3.00mm 宽)裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘
LTC3604IMSE#PBF 功能描述:IC REG BUCK SYNC 2.5A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压(升压) 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型,TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT
LTC3604IMSE#TRPBF 功能描述:IC REG BUCK SYNC 2.5A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压(升压) 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型,TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT