- 您现在的位置：买卖IC网 > PDF目录1830 > LTC3615EFE#PBF (Linear Technology)IC REG BUCK SYNC ADJ 3A 24TSSOP PDF资料下载
参数资料
| 型号： | LTC3615EFE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/32页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 3A 24TSSOP |
| 标准包装： | 62 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 0.6 V ~ 5.5 V |
| 输入电压： | 2.25 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 400kHz ~ 4MHz |
| 电流 - 输出： | 3A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 24-TSSOP 裸露焊盘 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC3615/LTC3615-1
PIN FUNCTIONS
(FE/UF)
PHASE (Pin 1/Pin 4): Phase Shift Selection. If pin is tied
to SGND, the phase between SW1 and SW2 will be 0°
(LTC3615) or 140° (LTC3615-1). With the PHASE pin
tied to half of the SV IN voltage, 90° (LTC3615) or 140°
(LTC3615-1) of phase shift will be selected. Tying PHASE
to SV IN will select 180° (LTC3615 and LTC3615-1).
V FB2 (Pin 2/Pin 5): Voltage Feedback Input Pin for Chan-
nel 2. See V FB1 .
ITH2 (Pin 3/Pin 6): Error Amplifier Compensation of
Channel 2. See ITH1.
TRACK/SS2 (Pin 4 /Pin 7): Internal, External Soft-Start,
External Reference Input for Channel 2. See TRACK/SS1.
SGND (Pin 5/Pin 8): Signal Ground. All small-signal and
compensation components should connect to this ground
pin which, in turn, should be connected to PGND at one
point.
PV IN2 (Pins 6, 7/Pins 9, 10) Channel 2 Power Supply
Input. See PV IN1 .
SW2 (Pins 8, 9/Pins 11, 12): Channel 2 Switching Node.
See SW1.
RUN2 (Pin 10/Pin 13): Enable Pin for Channel 2. See RUN1.
RUN1 (Pin 11/Pin 14): Enable Pin for Channel 1. Forcing
RUN1 above the input threshold enables the output SW1 of
channel 1. Forcing both RUNx pins to ground shuts down
the LTC3615. In shutdown, all functions are disabled and
the LTC3615 draws <1μA of supply current.
R T /SYNC (Pin 12/Pin 15): Oscillator Frequency. This pin
provides three modes of setting the switching frequency.
1. Connecting a resistor from R T /SYNC to ground will set
the switching frequency based on the resistor value.
2. Driving R T /SYNC with an external clock signal will
synchronize the switcher to the applied frequency. The
slope compensation is automatically adapted to the
external clock frequency.
3. Tying this pin to SV IN enables the internal 2.25MHz
oscillator frequency.
PGOOD2 (Pin 13/Pin 16): Power Good Output for
Channel 2. See PGOOD1.
SRLIM (Pin 14 /Pin 17): Slew Rate Limit. Slew rate on the
switch pins is programmed with the SRLIM pin:
1. Tying this pin to SGND selects maximum slew rate.
2. Minimum slew rate is selected when the pin is open.
3. Connecting a resistor from SRLIM to SGND allows the
slew rate to be continuously adjusted.
4. If SRLIM is tied to SV IN the slew rate is set to maxi-
mum and DDR mode is enabled (see the Applications
Information section).
PGOOD1 (Pin 15/Pin 18): Power Good Output Pin for
Channel 1. The open-drain output will be pulled down to
ground when the FB1 voltage of the channel is not within
the power good voltage window. The PGOOD1 will also be
pulled down if the channel is not enabled with the RUN1
pin or an undervoltage at SV IN is detected. In DDR mode
(SRLIM = SV IN ), the power good window moves in relation
to the actual TRACK/SS pin voltage.
SW1 (Pins 17, 16/Pins 19, 20): Channel 1 Switching
Node. Connection to the external inductor. This pin con-
nects to the drains of the internal synchronous power
MOSFET switches.
PV IN1 (Pins 18, 19/Pins 21, 22): Channel 1 Power Supply
Inputs. These pins connect to the source of the internal
power P-channel MOSFET of channel 1. P VIN1 and P VIN2
are independent of each other. They may connect to equal
or lower supplies than S VIN .
SV IN (Pin 20/Pin 23) Signal Input Supply. This pin pow-
ers the internal control circuitry and is monitored by the
undervoltage lockout comparator.
TRACK/SS1 (Pin 21/Pin 24): Internal, External Soft-Start,
External Reference Input for Channel 1. The type of start-up
9
For more information www.linear.com/LTC3615
3615fb
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3616IUDD#TRPBF | IC REG BUCK SYNC ADJ 6A 24QFN |
| LTC3617IUDD#TRPBF | IC REG SYNC 6A BUCK 24QFN |
| LTC3618EFE#PBF | IC REG DUAL SYNC 3A BUCK 24TSSOP |
| LTC3619BIMSE#TRPBF | IC REG BUCK SYNC ADJ DL 10MSOP |
| LTC3620EDC-1#TRPBF | IC REG BUCK SYNC 1.1V 15MA 8DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3615EUF#PBF | 功能描述:IC REG BUCK SYNC ADJ 3A DL 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3615EUF#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 3A DL 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3615EUF-1#PBF | 功能描述:IC REG BUCK SYNC ADJ 3A DL 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3615EUF-1#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 3A DL 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3615EUFPBF | 制造商:Linear Technology 功能描述:Dual 4MHz 3A Synch Step-Down DC/DC QFN24 |
发布紧急采购，3分钟左右您将得到回复。