- 您现在的位置：买卖IC网 > PDF目录14802 > LTC3616EUDD#PBF (Linear Technology)IC REG BUCK SYNC ADJ 6A 24QFN PDF资料下载
参数资料
| 型号： | LTC3616EUDD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 16/28页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 6A 24QFN |
| 标准包装： | 73 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 5.5 V |
| 输入电压： | 2.25 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 300kHz ~ 4MHz |
| 电流 - 输出： | 6A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 24-QFN 裸露焊盘（3x5） |
| 产品目录页面： | 1335 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC3616
APPLICATIONS INFORMATION
8 ? f SW ? C OUT ?
C OUT ≈
OutputCapacitor(C OUT )Selection
The selection of C OUT is typically driven by the required
ESR to minimize voltage ripple and load step transients
(low ESR ceramic capacitors are discussed in the next
section). Typically, once the ESR requirement is satisfied,
the capacitance is adequate for filtering. The output ripple
? V OUT is determined by:
? 1 ?
? V OUT ≤ ? I L ? ? ESR + ?
?
where f OSC = operating frequency, C OUT = output capaci-
tance and ? I L = ripple current in the inductor. The output
ripple is highest at maximum input voltage since ? I L
increases with input voltage.
In surface mount applications, multiple capacitors may
have to be paralleled to meet the capacitance, ESR or RMS
current handling requirement of the application. Aluminum
electrolytic, special polymer, ceramic and dry tantalum
capacitors are all available in surface mount packages.
Tantalum capacitors have the highest capacitance density,
but can have higher ESR and must be surge tested for
use in switching power supplies. Aluminum electrolytic
capacitors have significantly higher ESR, but can often
be used in extremely cost-sensitive applications provided
that consideration is given to ripple current ratings and
long-term reliability.
Ceramic Input and Output Capacitors
Ceramic capacitors have the lowest ESR and can be cost
effective, but also have the lowest capacitance density,
high voltage and temperature coefficients, and exhibit
audible piezoelectric effects. In addition, the high Q of
ceramic capacitors along with trace inductance can lead
to significant ringing.
They are attractive for switching regulator use because
of their very low ESR, but great care must be taken when
using only ceramic input and output capacitors.
Ceramic capacitors are prone to temperature effects
which require the designer to check loop stability over
the operating temperature range. To minimize their large
temperature and voltage coefficients, only X5R or X7R
ceramic capacitors should be used.
When a ceramic capacitor is used at the input and the power
is being supplied through long wires, such as from a wall
adapter, a load step at the output can induce ringing at
the V IN pin. At best, this ringing can couple to the output
and be mistaken as loop instability. At worst, the ringing
at the input can be large enough to damage the part.
Since the ESR of a ceramic capacitor is so low, the input
and output capacitor must instead fulfill a charge storage
requirement. During a load step, the output capacitor must
instantaneously supply the current to support the load until
the feedback loop raises the switch current enough to sup-
port the load. The time required for the feedback loop to
respond is dependent on the compensation components
and the output capacitor size. Typically, 3 to 4 cycles are
required to respond to a load step, but only in the first cycle
does the output drop linearly. The output droop, V DROOP ,
is usually about 2 to 4 times the linear drop of the first
cycle; however, this behavior can vary depending on the
compensation component values. Thus, a good place to
start is with the output capacitor size of approximately:
3.5 ? ? I OUT
f SW ? V DROOP
This is only an approximation; more capacitance may
be needed depending on the duty cycle and load step
requirements.
In most applications, the input capacitor is merely required
to supply high frequency bypassing, since the impedance
to the supply is very low.
16
For more information www.linear.com/LTC3616
3616fb
相关PDF资料 |
PDF描述 |
|---|---|
| CDR125NP-680MC | POWER INDUCTOR 68UH 1.26A SMD |
| LT3508IUF#PBF | IC REG BUCK ADJ 1.4A DL 24QFN |
| LT1976EFE#PBF | IC REG BUCK ADJ 1.5A 16TSSOP |
| RBM12DRMN-S664 | CONN EDGECARD 24POS .156 WW |
| LTC3442EDE#PBF | IC REG BUCK BOOST SYNC ADJ 12DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3616HUDD#PBF | 制造商:Linear Technology 功能描述:IC REG BUCK SYNC ADJ 6A 24QFN |
| LTC3616IUDD#PBF | 功能描述:IC REG BUCK SYNC ADJ 6A 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3616IUDD#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 6A 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3616MPUDD#PBF | 制造商:Linear Technology 功能描述:IC REG BUCK SYNC ADJ 6A 24QFN |
| LTC3616MPUDD#TRPBF | 制造商:Linear Technology 功能描述:IC REG BUCK SYNC ADJ 6A 24QFN |
发布紧急采购，3分钟左右您将得到回复。