- 您现在的位置：买卖IC网 > PDF目录79826 > LTC3633IFE#PBF (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, PDSO28 PDF资料下载
参数资料
| 型号： | LTC3633IFE#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, PDSO28 |
| 封装： | LEAD FREE, PLASTIC, TSSOP-28 |
| 文件页数： | 6/28页 |
| 文件大小： | 384K |
| 代理商： | LTC3633IFE#PBF |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC3633
14
3633f
APPLICATIONS INFORMATION
must instantaneously supply the current to support the load
until the feedback loop raises the switch current enough
to support the load. The time required for the feedback
loop to respond is dependent on the compensation and the
output capacitor size. Typically, 3 to 4 cycles are required
to respond to a load step, but only in the rst cycle does
the output drop linearly. The output droop, VDROOP, is
usually about 3 times the linear drop of the rst cycle.
Thus, a good place to start is with the output capacitor
size of approximately:
C
OUT ≈
3 ΔIOUT
f V
DROOP
Though this equation provides a good approximation, more
capacitance may be required depending on the duty cycle
and load step requirements. The actual VDROOP should be
veried by applying a load step to the output.
Using Ceramic Input and Output Capacitors
Higher values, lower cost ceramic capacitors are available
in small case sizes. Their high ripple current, high voltage
rating and low ESR make them ideal for switching regulator
applications. However, due to the self-resonant and high-
Q characteristics of some types of ceramic capacitors,
care must be taken when these capacitors are used at
the input. When a ceramic capacitor is used at the input
and the power is supplied by a wall adapter through long
wires, a load step at the output can induce ringing at the
VIN input. At best, this ringing can couple to the output
and be mistaken as loop instability. At worst, a sudden
inrush of current through the long wires can potentially
cause a voltage spike at VIN large enough to damage the
part. For a more detailed discussion, refer to Application
Note 88.
When choosing the input and output ceramic capacitors,
choose the X5R and X7R dielectric formulations. These
dielectrics have the best temperature and voltage charac-
teristics of all the ceramics for a given value and size.
INTVCC Regulator Bypass Capacitor
An internal low dropout (LDO) regulator produces the
3.3V supply that powers the internal bias circuitry and
drives the gate of the internal MOSFET switches. The
INTVCC pin connects to the output of this regulator and
must have a minimum of 1μF ceramic decoupling capaci-
tance to ground. The decoupling capacitor should have
low impedance electrical connections to the INTVCC and
PGND pins to provide the transient currents required by
the LTC3633. This supply is intended only to supply ad-
ditional DC load currents as desired and not intended to
regulate large transient or AC behavior, as this may impact
LTC3633 operation.
Boost Capacitor
The LTC3633 uses a “bootstrap” circuit to create a voltage
rail above the applied input voltage VIN.Specically,aboost
capacitor, CBOOST, is charged to a voltage approximately
equal to INTVCC each time the bottom power MOSFET is
turned on. The charge on this capacitor is then used to
supply the required transient current during the remainder
of the switching cycle. When the top MOSFET is turned on,
the BOOST pin voltage will be equal to approximately VIN
+ 3.3V. For most applications, a 0.1μF ceramic capacitor
closely connected between the BOOST and SW pins will
provide adequate performance.
Low Power 2.5V Linear Regulator
The V2P5 pin can be used as a low power 2.5V regulated
rail. This pin is the output of a 10mA linear regulator
powered from the INTVCC pin. Note that the power from
V2P5 eventually comes from VIN1 since the INTVCC power
is supplied from VIN1. When using this output, this pin
must be bypassed with a 1μF ceramic capacitor. If this
output is not being used, it is recommended to short this
output to INTVCC to disable the regulator.
相关PDF资料 |
PDF描述 |
|---|---|
| LM4040B82IDCKRG4 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 8.192 V, PDSO5 |
| LM4040CIM3-10.0T&R | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 10 V, PDSO3 |
| LM4040DIZ-4.1T&R | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 4.096 V, PBCY3 |
| LS4001-7EPD1T | 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
| LS4001-7EPD7TB1 | 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3633IUFD#PBF | 功能描述:IC REG BUCK ADJ 3A DL 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:MIC23xxx HyperLight Load™ Regulators 标准包装:5,000 系列:HyperLight Load® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.8V 输入电压:2.7 V ~ 5.5 V PWM 型:混合物 频率 - 开关:4MHz 电流 - 输出:2A 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 包装:带卷 (TR) 供应商设备封装:8-MLF?（2x2） 产品目录页面:1094 (CN2011-ZH PDF) 其它名称:576-3303-2 |
| LTC3633IUFD#TRPBF | 功能描述:IC REG BUCK ADJ 3A DL 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3633IUFDPBF | 制造商:Linear Technology 功能描述:Conv DC-DC Dual Step-Down 3.6-15V QFN28 |
| LTC3634EFE#PBF | 功能描述:IC REG 15V 3A STEP DOWN 28-TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
| LTC3634EFE#TRPBF | 功能描述:IC CONV DDR DDR2 DDR3 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。