- 您现在的位置：买卖IC网 > PDF目录19812 > LTC3705EGN#TRPBF (Linear Technology)IC CTRLR OCP 16SSOP PDF资料下载
参数资料
| 型号： | LTC3705EGN#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/20页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR OCP 16SSOP |
| 标准包装： | 2,500 |
| 输出隔离： | 隔离 |
| 输入电压： | 18 V ~ 80 V |
| 输出电压： | 11V |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 带卷 (TR) |
LTC3705
APPLICATIO S I FOR ATIO
( V – s ) MAX =
Pulse Transformer
The pulse transformer that connects the LTC3706 to the
LTC3705 performs the dual functions of gate drive duty
cycle encoding and gate drive bias supply for the LTC3705
by way of the on-chip full-wave rectifier. The designs of the
LTC3705 and LTC3706 have been coordinated so that the
transformer turn ratio is:
N LTC3705 = 2N LTC3706
where N LTC3705 is the number of turns in the winding
connected to the FB/IN + and FS/IN – pins of the LTC3705
and N LTC3706 is the number of turns in the winding
connected to the PT + and PT – pins of the LTC3706. The
winding connected to the LTC3706 must be able to with-
stand volt-seconds equal to:
V CC
2 f
where V CC is the maximum supply voltage for the LTC3706
and f is the operating frequency of the LTC3706.
Auxiliary Supply
When used with the LTC3706, the LTC3705 does not
require an auxiliary supply to provide primary-side gate-
drive bias current. After start-up, primary-side gate drive
current is provided by the LTC3706 through a small pulse
transformer and the LTC3705’s on-chip rectifier.
However, when used as a standalone primary-side con-
troller, the LTC3705 may require a conventional gate-drive
bias supply as shown in Figure 3. The bias supply must be
V IN
POWER
TRANSFORMER
designed to keep the voltage on the V CC pin between the
absolute maximum of 15V and the gate-drive undervoltage
lockout of 7V.
The auxiliary supply is connected in parallel with V CC . The
linear regulator maintains V CC at 8V. If the auxiliary supply
produces more than 8V, it turns off the external NMOS
before the LTC3705 can time out the linear regulator. If the
auxiliary supply produces less than 8V, the linear regulator
times out and then the voltage on the V CC pin declines to
the voltage produced by the auxiliary supply.
Slave Mode Operation
When the LTC3705 is paired with the LTC3706, multiple
pairs can be used to form a PolyPhase converter. In
PolyPhase operation, one LTC3705 becomes the “master”
while the remainder become “slaves.” The master con-
trols start-up in the same manner as for the single-phase
converter, while the slaves do not begin switching until
receiving PWM information through their own pulse trans-
former from their corresponding LTC3706. To synchro-
nize operation, the SSFLT and V CC pins of the master are
connected to the corresponding pins of all the slaves. The
master is designated by connection of the frequency set
resistor to the FS/IN – pin while this resistor is omitted from
the slaves. For the slaves the NDRV pin is connected to the
V CC pin. See the following section on PolyPhase Applica-
tions for more detail.
PolyPhase Applications
Figure 4 shows the basic connections for using the LTC3705
and LTC3706 in PolyPhase applications. One of the phases
is always identified as the “master,” while all other phases
are “slaves.” For the LTC3705 (primary side), the master
performs the open-loop start-up and supplies the initial
NDRV
PRIMARY
WINDING N P
SECONDARY
WINDING N S
V CC voltage for the master and all slaves. The LTC3705
slaves are put into that mode by omitting the resistor on
LTC3705
V CC
GND
2.2 μ F
1mH
BAS21
BAS21
AUXILIARY
WINDING N A
3705 F03
FS/IN–. The LTC3705 slaves simply stand by and wait for
PWM signals from their respective pulse transformers.
Since the SSFLT pins of master and slave LTC3705s are
interconnected, a FAULT (overcurrent, etc.) on any one of
the phases will perform a shutdown/restart on all phases
Figure. 3. Auxiliary Supply for Primary-Side Control
together.
3705fb
13
相关PDF资料 |
PDF描述 |
|---|---|
| LCMXO640E-5T144C | IC PLD 640LUTS 113I/O 144-TQFP |
| HSC40DREI-S13 | CONN EDGECARD 80POS .100 EXTEND |
| EEM24DTMH | CONN EDGECARD 48POS R/A .156 SLD |
| MIC2940A-5.0BT | IC REG LDO 5V 1.25A TO220-3 |
| GEM18DTAD-S189 | CONN EDGECARD 36POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3705IGN | 制造商:Linear Technology 功能描述:Forward Controller and Gate Driver 16-Pin SSOP N |
| LTC3705IGN#PBF | 功能描述:IC CTRLR OCP 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - AC-DC 转换器，离线开关 系列:- 标准包装:3,000 系列:- 输出隔离:隔离 频率范围:61kHz ~ 71kHz 输入电压:9.4 V ~ 28 V 输出电压:12V 功率（瓦特）:- 工作温度:-40°C ~ 125°C 封装/外壳:SC-74，SOT-457 供应商设备封装:6-TSOP 包装:带卷 (TR) |
| LTC3705IGN#TRPBF | 功能描述:IC CTRLR OCP 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - AC-DC 转换器，离线开关 系列:- 标准包装:3,000 系列:- 输出隔离:隔离 频率范围:61kHz ~ 71kHz 输入电压:9.4 V ~ 28 V 输出电压:12V 功率（瓦特）:- 工作温度:-40°C ~ 125°C 封装/外壳:SC-74，SOT-457 供应商设备封装:6-TSOP 包装:带卷 (TR) |
| LTC3706EGN#PBF | 功能描述:IC SECONDARY SIDE CTRLR 24SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:PolyPhase® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| LTC3706EGN#TRPBF | 功能描述:IC SECONDARY SIDE CTRLR 24SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:PolyPhase® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。