参数资料
型号: LTC3722IGN-1#PBF
厂商: Linear Technology
文件页数: 7/28页
文件大小: 0K
描述: IC REG CTRLR DIV ISO PWM 24SSOP
标准包装: 55
PWM 型: 电流模式,全桥
输出数: 1
频率 - 最大: 1MHz
占空比: 98.5%
电源电压: 3.8 V ~ 10.3 V
降压:
升压:
回扫:
反相:
倍增器:
除法器:
Cuk:
隔离:
工作温度: -40°C ~ 85°C
封装/外壳: 24-SSOP(0.154",3.90mm 宽)
包装: 管件
LTC3722-1/LTC3722-2
PIN FUNCTIONS
(LTC3722-1/LTC3722-2)
SYNC (Pin 1/Pin 1): Synchronization Input/Output for the
Oscillator. The input threshold for SYNC is approximately
1.9V, making it compatible with both CMOS and TTL logic.
Terminate SYNC with a 5.1k resistor to GND.
DPRG (Pin 2/Pin 5): Programming Input for Default Zero
Voltage Transition (ZVS) Delay. Connect a resistor from
DPRG to V REF to set the maximum turn on delay for outputs
A, B, C, D. The nominal voltage on DPRG is 2V.
RAMP (NA/Pin 2): Input to Phase Modulator Comparator
for LTC3722-2 only. The voltage on RAMP is internally
level shifted by 650mV.
CS (Pin 3/Pin 3): Input to Phase Modulator for the
LTC3722-1. Input to pulse-by-pulse and overload current
limit comparators, output of slope compensation circuitry.
The pulse by pulse comparator has a nominal 300mV
threshold, while the overload comparator has a nominal
650mV threshold.
COMP (Pin 4/Pin 4): Error Amplifier Output, Inverting
Input to Phase Modulator.
R LEB (Pin 5/NA): Timing Resistor for Leading Edge Blank-
ing. Use a 10k to 100k resistor to program from 40ns to
310ns of leading edge blanking of the current sense signal
on CS for the LTC3722-1. A ±1% tolerance resistor is
recommended. The LTC3722-2 has a fixed blanking time
of approximately 80ns.
FB (Pin 6/Pin 6): Error Amplifier Inverting Input. This is
the voltage feedback input for the LTC3722. The nominal
regulation voltage at FB is 1.204V.
SS (Pin 7/Pin 7): Soft-Start/Restart Delay Circuitry Timing
Capacitor. A capacitor from SS to GND provides a controlled
ramp of the current command (LTC3722-1), or duty cycle
(LTC3722-2). During overload conditions SS is discharged
to ground initiating a soft-start cycle.
NC (Pin 8/Pin 8): No Connection. Tie this pin to GND.
PDLY (Pin 9/Pin 9): Passive Leg Delay Circuit Input. PDLY
is connected through a voltage divider to the left leg of
the bridge in adaptive ZVS mode. In fixed ZVS mode, a
voltage between 0V and 2.5V on PDLY, programs a fixed
ZVS delay time for the passive leg transition.
SBUS (Pin 10/Pin 10): Line Voltage Sense Input. SBUS is
connected to the main DC voltage feed by a resistive volt-
age divider when using adaptive ZVS control. The voltage
divider is designed to produce 1.5V on SBUS at nominal
V IN . If SBUS is tied to V REF , the LTC3722-1/LTC3722-2 is
configured for fixed mode ZVS control.
ADLY (Pin 11/Pin 11): Active Leg Delay Circuit Input. ADLY
is connected through a voltage divider to the right leg of
the bridge in adaptive ZVS mode. In fixed ZVS mode, a
voltage between 0V and 2.5V on ADLY, programs a fixed
ZVS delay time for the active leg transition.
UVLO (Pin 12/Pin 12): Input to Program System Turn-
On and Turn-Off Voltages. The nominal threshold of the
UVLO comparator is 5V. UVLO is connected to the main
DC system feed through a resistor divider. When the
UVLO threshold is exceeded, the LTC3722-1/LTC3722-2
commences a soft-start cycle and a 10μA (nominal) cur-
rent is fed out of UVLO to program the desired amount of
system hysteresis. The hysteresis level can be adjusted
by changing the resistance of the divider.
SPRG (Pin 13/Pin 13): A resistor is connected between
SPRG and GND to set the turn-off delay for the synchronous
rectifier driver outputs (OUTE and OUTF). The nominal
voltage on SPRG is 2V.
V REF (Pin 14/Pin 14): Output of the 5V Reference. V REF
is capable of supplying up to 18mA to external circuitry.
V REF should be decoupled to GND with a 1μF ceramic
capacitor.
OUTF (Pin 15/Pin 15): 50mA Driver for Synchronous
Rectifier Associated with OUTB and OUTC.
OUTE (Pin 16/Pin 16): 50mA Driver for Synchronous
Rectifier Associated with OUTA and OUTD.
OUTD (Pin 17/Pin 17): 50mA Driver for Low Side of the
Full Bridge Active Leg.
V CC (Pin 18/Pin 18): Supply Voltage Input to the
LTC3722-1/LTC3722-2 and 10.25V Shunt Regulator.
The chip is enabled after V CC has risen high enough to
allow the V CC shunt regulator to conduct current and the
UVLO comparator threshold is exceeded. Once the V CC
shunt regulator has turned on, V CC can drop to as low as
6V (typ) and maintain operation.
372212fb
For more information www.linear.com/LTC3722
7
相关PDF资料
PDF描述
ISC1210BN120J INDUCTOR WW 12UH 5% 1210
VI-25Z-EU-F2 CONVERTER MOD DC/DC 2V 80W
SRP1040-R80M INDUCTOR 800NH 21A SMD
LT3724MPFE#PBF IC REG CTRLR BST INV PWM 16TSSOP
LTC3729EUH IC REG CTRLR BUCK PWM CM 32-QFN
相关代理商/技术参数
参数描述
LTC3722IGN-2#PBF 功能描述:IC REG CTRLR DIV ISO PWM 24SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LTC3722IGN-2#TRPBF 功能描述:IC REG CTRLR DIV ISO PWM 24SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LTC3723EGN-1 功能描述:IC REG CTRLR FLYBK ISO CM 16SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LTC3723EGN-1#2EYPBF 制造商:Linear Technology 功能描述:
LTC3723EGN-1#PBF 功能描述:IC REG CTRLR FLYBK ISO CM 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR