- 您现在的位置：买卖IC网 > PDF目录4959 > LTC3786EMSE#PBF (Linear Technology)IC REG CTRLR BST PWM CM 16-MSOP PDF资料下载
参数资料
| 型号： | LTC3786EMSE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 17/34页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST PWM CM 16-MSOP |
| 标准包装： | 37 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 850kHz |
| 占空比： | 100% |
| 电源电压： | 4.5 V ~ 38 V |
| 降压： | 无 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-TFSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
LTC3786
APPLICATIONS INFORMATION
I OUT(MAX) ? ( V OUT – V IN(MIN) ) V
V RIPPLE =
V OUT = 1.2V ? 1 + B ?
R B
accountsforthelosscausedbyreverserecoverycurrent,
is inversely proportional to the gate drive current and has
an empirical value of 1.7.
Both MOSFETs have I 2 R losses while the bottom N-channel
equation includes an additional term for transition losses,
which are highest at low input voltages. For high V IN the
high current efficiency generally improves with larger
MOSFETs, while for low V IN the transition losses rapidly
increase to the point that the use of a higher R DS(ON) device
with lower C MILLER actually provides higher efficiency. The
synchronous MOSFET losses are greatest at high input
voltage when the bottom switch duty factor is low or dur-
ing overvoltage when the synchronous switch is on close
to 100% of the period.
The term (1 + δ ) is generally given for a MOSFET in the
form of a normalized R DS(ON) vs Temperature curve, but
δ = 0.005/°C can be used as an approximation for low
voltage MOSFETs.
C IN and C OUT Selection
The input ripple current in a boost converter is relatively
low (compared with the output ripple current), because
this current is continuous. The input capacitor, C IN , volt-
age rating should comfortably exceed the maximum input
voltage. Although ceramic capacitors can be relatively
tolerant of overvoltage conditions, aluminum electrolytic
capacitors are not. Be sure to characterize the input voltage
for any possible overvoltage transients that could apply
excess stress to the input capacitors.
The value of the C IN is a function of the source impedance,
and in general, the higher the source impedance, the higher
the required input capacitance. The required amount of
input capacitance is also greatly affected by the duty cycle.
High output current applications that also experience high
duty cycles can place great demands on the input supply,
both in terms of DC current and ripple current.
In a boost converter, the output has a discontinuous current,
so C OUT must be capable of reducing the output voltage
ripple. The effects of ESR (equivalent series resistance)
and the bulk capacitance must be considered when choos-
ing the right capacitor for a given output ripple voltage.
The steady ripple voltage due to charging and discharging
the bulk capacitance in a single phase boost converter is
given by:
C OUT ? V OUT ? f
where C OUT is the output filter capacitor.
The steady ripple due to the voltage drop across the ESR
is given by:
? V ESR = I L(MAX) ? ESR
Multiple capacitors placed in parallel may be needed to
meet the ESR and RMS current handling requirements.
Dry tantalum, special polymer, aluminum electrolytic and
ceramic capacitors are all available in surface mount
packages. Ceramic capacitors have excellent low ESR
characteristics but can have a high voltage coefficient.
Capacitors are now available with low ESR and high ripple
current ratings (i.e., OS-CON and POSCAP).
Setting Output Voltage
The LTC3786 output voltage is set by an external feedback
resistor divider carefully placed across the output, as shown
in Figure 3. The regulated output voltage is determined by:
? R ?
? R A ?
Great care should be taken to route the VFB line away
from noise sources, such as the inductor or the SW line.
Also, keep the VFB node as small as possible to avoid
noise pickup.
V OUT
LTC3786
VFB
R A
3786 F03
Figure 3. Setting Output Voltage
3786fa
17
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3865EUH#PBF | IC REG CTRLR BUCK PWM CM 32-QFN |
| GSC31DRES-S93 | CONN EDGECARD 62POS .100 EYELET |
| GMC31DRES-S93 | CONN EDGECARD 62POS .100 EYELET |
| ESC31DREI-S93 | CONN EDGECARD 62POS .100 EYELET |
| RMC15DRAN-S734 | CONN EDGECARD 30POS .100 R/A PCB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3786EUD#PBF | 功能描述:IC REG CTRLR BST PWM CM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LTC3786EUD#PBF | 制造商:Linear Technology 功能描述:IC, DC-DC CONV, 550kHz, QFN16 |
| LTC3786EUD#TRPBF | 功能描述:IC REG CTRLR BST PWM CM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3786IMSE#PBF | 功能描述:IC REG CTRLR BST PWM CM 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3786IMSE#TRPBF | 功能描述:IC REG CTRLR BST PWM CM 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。